Tag Archives: vegan chocolate cupcakes

2015/10/09 (F) All Charged Up

Leave a reply

We finished the current batch of granola for breakfast and had just finished our meal when Chris, from Bratcher Electric, showed up at 8:45 AM to service the whole house generator.  He let me watch and explained the various steps in the process.  The trickiest part appeared to be replacing the spark plug on the back side of the engine.  Everything else was fairly accessible.  There is a 1/4 turn valve to drain the oil and a rubber tube to get it out to a collection vessel.

Chris had what looked like a small gas can but it was painted blue.  It had a clear plastic tube attached to what would normally be the air vent.  The tube was sized to just fit inside the oil drain hose.  A vacuum pump was threaded on to opening where the pour spout would normally go.  A few pumps of the handle and the device sucked the oil right out of the engine and contained it so he could transport it easily and cleanly.  It was a very clever device, and obviously very handy for someone who does several generator maintenance procedures every day.

He gapped the spark plugs at 0.028″, checked the air filter (it was fine), replaced the oil filter, noting the date on the filter with a permanent marker, and put ~2-1/3 quarts of 5W-30 synthetic oil back in the engine.  He cautioned me to only use the specified filter and pure synthetic oil.  The engine runs hot under load and regular oil can lead to problems.  He checked all of the settings and changed the weekly self-test to run at full speed for the entire time.  He prefers that setting as it gets the engine up to normal operating temperature and helps burn off any moisture in the oil.  He started the unit manually, let it run for a while, and then shut it down and put in back in AUTO mode.

Linda prepared the dry ingredients for her vegan chocolate cupcakes and then put together a grocery list.  She left to go to Meijer’s while Chris was still working.  He finished up around 10:15.  I worked on the bus, using split plastic wire loom to protect the wires that power the fans on the heat exchangers.  I then worked on reconnecting the wires from the front bay electric heater to the supply wires.

A close up view of the fill/bleeder valve assembly for the heat exchangers in the desk bases.

A close up view of the fill/bleeder valve assembly for the heat exchangers in the desk bases.

The supply wires run inside the HVAC duct.  They originally came out of the duct and went through a hole in the floor into the OTR air-conditioning bay and then through the partition wall into the front bay.  I had to cut the cable and pull it through the floor from underneath so I could install the new floor tile.  I could clearly see where the OTR HVAC supply duct came into the distribution duct but when I tried drilling from below I seemed to hit metal.   The bottom of the duct was clearly plywood so I drilled from above with a 1/2″ spade bit.  I got through most of the plywood but again seem to hit metal.  I knew there wasn’t anything in that location, like wires, pipes, or air lines, so I switched to a 1/2″ twist drill and finished the hole.

I dropped a screwdriver through the hole so I could locate it from below.  I then pushed the electrical cable from the heater up through the hole and secured it to a fastener on the forward wall with a cable tie.  Linda got back at this point so I helped get the groceries into the house.  She then mixed a new batch if granola and put it in the oven to bake.  I gathered up my electrical tools, uncapped the feed wires, checked them with a volt meter to make sure they were not energized, connected the feed wires to the load wires, and tucked them back inside the duct.

We had a choice as to what to work on next—fill the heat exchangers and hoses with antifreeze or hang the wallpaper in the hallway—so we had lunch.  Summer has passed, but tofu hotdogs with mustard, onion, and relish, along with some red grapes, was still a tasty lunch.

When we got back to work in the coach we decided to hang the wallpaper.  The pieces were already cut and laid out on the bed.  Hanging them not only got them off the bed, it would allow us to get the wood trim off the bed as well and back on the lower wall.  But not today.  The wallpaper adhesive needs to cure for 24 hours before we work around it and does not achieve its full cure for 5 to 7 days.  We have one piece of wallpaper to hang behind the forward end of the sofa but the wall prep is not finished in that area.  Once that piece is up, and we have the Corian top for the desk, we can complete the installation of the desk and sofa.

Shawna was bringing Madeline at 4:30 PM to spend the night with us.  It was already 2:30 and I needed to get cleaned up and put on non-work clothes before they arrived so we called it a day.  I had once again accumulated quite a few tools in the bus.  I gathered up all of the ones I was done with, returned them to the garage, and locked up the coach.  The UPS truck showed up with my package from B&H Photo which I set aside temporarily while I took a shower and got dressed.

The box looked like it had been treated well in shipment.  I opened the box, carefully removed all of the contents, and compared them to the order/packing list.  Everything was there and appeared to be in pristine condition.  I unwrapped the battery charger and Lithium ion battery, put the battery in the charger, and plugged it in.  The new charger is essentially the same as the one that came with my Sony alpha 100 years ago so I got the old one from the basement.  I bought five additional batteries so I opened one of them and plugged it in to the old charger.  I then found the Instruction Manual and curled up with it on the living room sofa while Juniper (the cat) curled up on me.

The directions with the charger and the batteries indicated that it can take up to 175 minutes to fully recharge a battery and that full charge is not obtained until an hour after the charging light goes out.  So, basically, I need to leave the batteries in the charger for three hours to ensure they are fully charged.  The camera takes one battery, and the vertical grip accessory takes two batteries, so my normal operating configuration will be to have three batteries in the use.  That’s why I have a total of six batteries for this new camera.  I will probably buy another charger so I can charge three batteries simultaneously.

I called Chuck to let him know I got my car back late yesterday but would not be able to move the windshields box until sometime next week.  It turned out that he and Barbara were also busy all weekend.  His daughter, son-in-law, and grandson were in town with more family arriving from Trinidad and Tobago this evening.  Tomorrow is his grandson’s first birthday and Sunday he is being baptized at the church in Ann Arbor where Chuck’s daughter was married.

Shawna showed up just after 4:30 PM.  Madeline had fallen asleep in the car and was slow to wake up, clinging to her mom for quite a while.  Linda brought in the various bags of clothes and toys along with the inflatable bed and got everything situated in the middle bedroom.  When Linda mentioned making cupcakes Madeline finally woke up and became cheerful.  Once her focus was on baking with Grandma Linda Shawna was able to slip away without any drama on Ms. M’s part.

Today was Brendan and Shawna’s friend Jorge’s birthday and the three of them were headed to a new restaurant in Detroit to celebrate.  The restaurant does not take reservations and is apparently very popular at the moment so Shawna was not sure if they would actually get to eat there.

With Linda’s help Madeline mixed the ingredients for the cupcakes and managed to pour most of the batter into the baking tray.  Linda then prepared dinner while I played with Madeline.  We did the ABCs on her placemat, and then colored with crayons.  Dinner was mock chicken tenders, edamame, and steamed carrot rounds with fresh orange segments and sliced strawberries, so it was mostly fresh, whole plant-based foods.

As soon as the cupcakes were cool enough to be frosted Madeline coated each one with the special Halloween orange frosting and the back and orange Halloween sprinkles.  I was summoned to inspect the work and then it was time to eat.  Madeline selected a cupcake for herself and then one for me and one for Linda.  We ate them at the table and they were very good.

After cupcakes we played soccer with two different balls, kicking and throwing them all around the house.  By 8 PM we needed to start winding things down.  Shawna had left her iPad and Madeline selected a Curious George video about Christmas.  Linda and Madeline climbed up in our bed where they could stretch out their legs and watched the first 60% of the cartoon.  I opened two more camera batteries and put them in the chargers and then joined the girls.  We will watch the rest of the cartoon tomorrow morning.

I helped Madeline brush her teeth and Linda got her into her pajamas.  Linda read her several stories and finally got her in bed around 9:15 PM.  During dinner Madeline inquired about having pancakes for breakfast.  (I had made the same inquiry over lunch.)  Linda did not have all of the ingredients she needed so after Madeline went to bed I went to Meijer’s in Howell and bought avocado oil and all-purpose flour.  Linda is trying to use up ingredients rather than stock up on them so I bought a two pound bag of King Arthur organic unbleached enriched all-purpose flour even though I could have bought a 10 pound bag of the Meijer’s brand (bleached and not organic) for only 50 cents more.

Just before going to bed I opened two more batteries and put them in the chargers.  We went to bed at 11 PM but did not turn on the TV to ensure that we did not disturb Madeline’s sleep.  I was basically done with the draft of this post and read some more of the Instruction Manual for my new Sony alpha 99 (SLT-A99V) camera and vertical battery grip (VG-C99AM).  I am really looking forward to using this new equipment but it takes a couple of days to charge batteries, install software, and read manuals enough to be able to configure it for first use.  This class of camera has a lot of adjustable parameters with default settings that may or may not be what any particular user wants.

 

2015/09/06 (N) Grouting

Leave a reply

We got up quietly at 7:30 AM as Madeline was still sound asleep.  Linda did not want to let her sleep too long and get off schedule so I got the “all clear” to grind the coffee beans just before 8 AM.  I made the Costa Rican half-caff because I am trying to use it up so we can replace it with something we like better.  Madeline emerged with Grandma Linda a few minutes later.  After stretching they decided to sit quietly on the living room sofa and read stories while everyone woke up and the adults enjoyed our coffee.

Sometime between 9:30 and 10 AM we left for the Howell Farmers Market.  We walked from one end to the other, with Madeline in her stroller, scoping out this week’s bounty. We then walked back through and Linda bought a few things including hard stem garlic which we had never seen before.  We stopped and chatted with our favorite vendor, Marjorie.

When we got home and put the produce away Linda prepared a snack lunch for herself and Madeline.  The two of them then went on an outing to the farm at Kensington Metropark (KMP) while I stayed behind to work on bus projects.  I decided to start by finishing the assembly of the pieces for the built-in sofa.  I attached the center support for the return air shelf as follows:

  • I determined the center of the long edges of the shelf and drew a line between them.
  • I carried these center marks to the other side and then measured 3/8″ to either side.
  • I connected corresponding marks to create a pair of parallel lines 3/4″ apart and centered on the underside of the shelf.
  • I placed the support in position, determined its fore-aft position, and marked the ends.
  • I then marked a piece of scrap wood, cut it into four pieces, and used them to hold the support in place; two long pieces the same length as the support, and two short pieces across the ends.
  • This allowed me to turn the shelf right side up with the center support held in the correct place and then mark and drill countersunk pilot holes for the screws.
  • I removed the support piece, sanded off any rough spots, put Titebond II wood glue on the edge, and replaced it between the temporary blocking.
  • I stood on the shelf to force the pieces together and ran all the screws down tight.
  • I then removed the temporary blocking.

After sleeping on it last night I decided I would attach the plenum/support boxes to the vertical front panel and the wood wire chase on top of the HVAC chase rather than to the adjacent cabinets or to the floor.  That meant I could go ahead and assemble them as complete, single units.  Easier said than done.

Even though I used right angle corner clamps the two halves I built for each box did not want to go together perfectly.  I managed to get one of them assembled but could not complete the other one by myself.  The problem was that I needed both hands to pull the pieces into alignment and two more hands to operate the drill and screw gun.

By now it was 1 PM, which is Madeline’s normal nap time, but they were not back from the Metropark yet so I gathered up all of the tools and materials I needed to grout the floor tiles in the bus.  That included the special Armstrong S-288 Glacier White sanded vinyl grout, a flat blade screwdriver, the 4″x8″ hard edge float, the smaller margin trowel, the 2″ putty knife (wall scraper), the ScotchBrite sponges, the Revel scrubber, two large buckets for rinse water, paper towels, a large cloth towel, and paper bags.

Madeline pets one of the sheep at the Kensington Metropark animal farm.

Madeline pets one of the sheep at the Kensington Metropark animal farm.

Since Linda and Madeline had still not returned I had a few pretzels with hummus.  They finally got home around 1:30 PM and I heard all about the farm and the animals Ms. M got to see and touch.  The 2-day old piglets were apparently a big hit but so was the playroom.  It was a good outing and I wish I could have gone but I got stuff done that needed to be done.

Madeline finally laid down for her nap at 2 PM but Linda could not help me with the tile grouting as she needed to be within earshot of Madeline’s bedroom.  I decided that we could not afford any further delay for this aspect of the interior remodeling project and resolved to do it by myself.  Without Linda to walk me through the steps, have materials ready, and clean the tools, I needed to be very clear about the steps and their timing.  I must have read the directions on the container of grout a dozen times in an attempt to internalize them but they just would not stick with me.  I needed a spray bottle for water so Linda found one for me.

The afternoon was very warm so I turned off the air-conditioning in our home library, closed up the coach, and turned on two of the three air-conditioners, making sure they were on opposite legs of the electrical service.  I staged all of the stuff in the bedroom storage box as I planned to start on the back side of the bed in the driver side corner by the head of the bed and work my way out.

I finally got started at 2:30 PM.  The grouting involved a specific set of steps that got repeated many times as the directions said to only do 6 – 10 sq. ft. at a time.  That range had to do with the time required to apply and strike the grout, setup time (3 – 8 minutes), misting with water, waiting 20-30 seconds, scrubbing, and finally wiping with a square edged cellulose sponge.  I had to divide the U-shaped bedroom floor into six sections and it took me until 5:30 PM to do that much so my average time was 30 minutes per section, each of which was smaller than 6 square feet.

I took a short break, had something to drink, and checked with Linda on the timing of dinner.  We settled on 6:30 PM and I returned to my grouting.  I had to do the bathroom floor in two sections, which got me into the hallway and joined up with the work from the bedroom.  I went in to clean up for dinner and was greeted by the smell of something baking.  Madeline wanted to make cupcakes so Linda assembled the ingredients and walked her through the steps, letting her do as much of the work as possible.  For not even being three years old yet she is very interested in cooking, but only if it is something she will get to eat! 🙂

Dinner was vegan cheeseburgers, corn-on-the-cob (from the Farmers Market), left over black beans and edamame, and sliced pears.  I worked in the bus from 7 to 8 PM and finished the hallway as far as the bend that transitions into the kitchen.  I cleaned all of the tools and sealed the grout container using Cling-Wrap pressed down onto the surface of the grout to keep air away from it, and locked up the bus.

I washed up and turned on the Yaesu FTM-400 2m/70cm radio in the ham shack while Linda helped Madeline take a bath.  Steve, N8AR, was serving as net control for the weekly SLAARC information net and had already started the net but not yet called for check-ins so I got to participate in the entire net.  We had a small group this evening, most likely due to it being a holiday weekend, but it was still a good net.

I came upstairs to have dessert with Linda and Madeline; chocolate cupcakes (vegan) with sprinkles.  Yum.  I then returned to my office to re-read an article I wrote about replacing the speedometer in the bus and editing it to indicate where the pictures should be placed.  I dealt with several BCM related e-mails and then came upstairs.

Madeline was in her pajamas and sitting in her portable bed while Linda read a story.  She decided that she wanted me to read a couple stories too, so I did.  We got her tucked in with her stuffed animals arranged at the four corners of her bed, turned on the night light, and left her to fall asleep.

I opened the bottle of Apricot wine that Brendan and Shawna picked up from Leelenau Cellars and we each had a small glass.  I worked on this post while Linda cleaned up the kitchen.  It had been a long and very tiring day for both of us but a very satisfying and productive day as well.  We don’t mind that kind of tired.

 

2015/07/18 (S) RV Shopping

Leave a reply

Madeline was awake at 7 AM and Linda got her up shortly after that.  I slept in until 8 AM.  They had already eaten breakfast by then so I made coffee and had cinnamon raisin toast.  Metropolitan Baking Company makes a very tasty cinnamon raisin bread.  We all sat in the living room while Madeline played with various toys and I worked on finishing yesterday’s blog post.

Linda and Madeline left at 10 AM for the Howell Library.  The plan was to let Madeline play in the children’s area, which has a lot interesting things to do for children her age.  After selecting some books and DVDs to bring home they were headed to Meijer’s to do some grocery shopping.

I continued working on my iPad until Mara came in the house.  We had a chat about blogging and I showed her the Feedly app on my iPad.  She has attended workshops put on by The Geeks On Tour and has their training materials.  I think Blogger is probably the right tool for her and Picasa is probably the right way to manage her photos.  They are both Google products so they work well together and they are free to use.  There are downsides to that, especially for professionals, but for most people it’s a great solution.

Mara and I left around 11:45 AM and drove to General RV in Wixom.  This was my first visit to their new facility and it is nice.  The parts department is larger and better stocked than the old one and is bright with natural light from large south and west facing windows.  We were asked several times if we needed assistance but we were never pestered.  They did not have any of the white Dicor self-leveling caulk we were looking for but one of the employees checked their stock and brought out six tubes.  Mara bought four of them along with a new Norcold refrigerator roof vent cover, a small roll of Eternabond tape, and some concentrated RV wash/wax.  I picked up eight brown circular adjustable air vents for the bus.  The ones in there now are black but I think the brown will look better with the new floor tile.  We won’t really know, however, until we install them.

We drove to Lowe’s in Howell where I bought two pieces of 12″ x 18″ thin galvanized steel plate and three rolls of 3M double-sided tape suitable for outdoor use.  The plan is to put one of these on the roof of Mara’s motorhome and possibly put the other on the roof of our bus to allow the use of the magnetic base cell phone antennas that came as part of the weBoost Drive 4G-X cellular booster systems.  Once the steel sheets are affixed to the roof I will caulk around them.  First, however, I will just set the sheets up there and see what sort of difference the system makes.

We stopped at O’Reilly’s auto parts store and Mara bought some 10, 15, and 20 Amp mini fuses.  These fuses have a small LED that glows if the fuse opens.  They were more expensive than the regular ones, but that is a very handy feature and I may stock up on these the next time I need to buy fuses.

Back at the house Linda informed me that when the storm blew in it pulled the sun umbrella out of the table on the deck.  We put the glass top back in the table and re-installed the umbrella.  This has happened a couple of times and we have been lucky that the glass top has not broken.  Mara returned to her rig.  She had left her patio awning out but it was not damaged.

Linda got Madeline up from her nap at 3 PM and read her a story about flying in an airplane.  Madeline then played with her toys for a while.  Around 4 PM Madeline wanted to bake a cake.  Linda was planning on this anyway but it was nice that it was Madeline’s idea.  They got busy in the kitchen and I sneaked off to my office for a while.

Madeline had dinner at 6 PM so I came up from my office while she ate.  Meals are a social time and I was ready for a break anyway.  After dinner Linda helped Madeline get cleaned up.  I slipped back down to my office while they watched an Elmo DVD, but by 7 PM I was done working on the pantry design for the evening and went back upstairs.  Linda was reading the airplane ride book (again), after which Madeline played (with) the organ after which they drew for a while and then played with the Play-Doh.  Madeline is a busy girl.

I was just getting ready to go ask Mara what temperature to preheat the oven when she came to the house with an armful of ingredients for the pizza.  She has a recipe for a wheat-free (gluten-free) pizza dough that she wanted us to try.  It calls for cheese and eggs so to make it vegan Linda had her buy Daiya mozzarella shreds and gave her egg replacer to use.  The other ingredients include almond meal, chickpea flour, golden flaxseed, onion powder, garlic powder, sea salt, olive oil (EVVO), and water.

It took another 25 minutes to get Madeline to bed but once Linda had her tucked in I opened a bottle of Nebiola wine from the St. Clair Winery in Deming, New Mexico.  I often write that I am not a fan of red wines and continue to not like dry wines with lots of tannins.  The Nebbiolo, however, is one of the nicest wines I think I have ever tried.  That probably means it is too sweet for most red wine drinkers, but I did not find it to be sweet; I found it to be smooth and complex.

We ordered a couple of things from Amazon on Wednesday and they showed up yesterday.  When I unboxed the Notier capacitive touch screen precision stylus I was surprised by what I found.  It’s a 2-part housing that unscrews and the cover screws onto the other end of the bottom part, which is needed for comfort and balance.  The stylus tip is small but has a 1/4 in clear plastic disc on the end.  It was on sale for $11 and I decided right away I would not return it.  Besides, I had not actually tried it yet.  So I finally tried it while the pizza was cooking.  It is an amazing little device!  It is, indeed, very precise and works with a delicate touch so I will have to re-calibrate my “typing” style, but it just goes to show that you never know until you try.

I lost track of time but it was somewhere between 9:30 and 10 PM when the pizza was ready to eat.  It was, however, worth the wait and might be the best vegan pizza I have ever had.  The recipe is definitely a keeper.  We each had a chocolate cupcake (with sprinkles) while we finished our wine.  We then adjourned to the living room and talked until almost 11 PM.  It was a very full day for all four of us and everyone was tired but satisfied.  It’s nice having family and friends here.

 

2015/07/05 (N) Return to HFM

Leave a reply
Madeline helps Grandma Linda mix the batter for vegan blueberry pancakes.

Madeline helps Grandma Linda mix the batter for vegan blueberry pancakes.

The day started with Grandma Linda’s fabulous, made from scratch, blueberry vegan pancakes for breakfast, which Madeline helped make!  After breakfast we took Madeline to the Howell Farmers Market (HFM).  She had been to this market with us once before and it was a beautiful Michigan summer morning for a return visit.  On the drive over we discussed why it is that you cannot buy a farmer at a farmers market and you cannot buy a garage at a garage sale.  English can be a funny/strange language.

We walked the entire market, which is not really that big, and Linda bought some fresh strawberries.  A couple of the regular vendors were missing.  In particular we wanted to buy some more soap from Marjorie but she was not there.  Madeline enjoyed checking out the child and doll sized wooden furniture that one vendor had for sale.  We kept an eye out for someone selling jelly beans but did not see any so we stopped at the CVS on the way home and got a small bag of them.

We had just gotten home and I was unlocking the front door when Brendan and Shawna arrived.  We had a nice visit and they stayed for a light lunch.  By the end of lunch Madeline was showing signs of being ready for her nap so Brendan transferred the car seat and stroller from Linda’s car to their car, gathered up all of Madeline’s things, and loaded their car.  Madeline left with her parents at 12:30 PM and Linda laid down for a nap shortly thereafter.

I looked at the SLAARC WordPress website on my iPad to make sure it was working.  I checked most of the pages except for the Member Only Area, which requires a login, and they appeared to be OK.  I then went to my office to deal with things that needed to be dealt with from there.

Madeline tries on a child sized rocking chair at the Howell Farmers Market.

Madeline tries on a child sized rocking chair at the Howell Farmers Market.

My first task was to update the roster and financial records for our FMCA Freethinkers Associate Chapter.  I sent e-mails to new members, uploaded the updated roster to our Dropbox, and e-mailed everyone that they were available.  I had received the draft copy of the June 2015 issue of Bus Conversion Magazine on Friday.  I proofread part 3 of my 4-part article on the exterior renovation of our motorcoach and sent corrections to the editor.  I then settled in to edit blog posts.

I took a break for dinner.  Linda cooked Brussels sprouts and heated some vegan riblets.  The barbecue sauce on these riblets is very tasty.  We had vegan chocolate cupcakes for dessert and they were very tasty too.  I then went back to my office and continued editing blog posts.

I took a break just before 8 PM to join the South Lyon 2m Information Net using our new Yaesu FTM-400DR/DE RADIO but I did not hear anything except noise.  I left the radio on for a while and then turned it off.  I switched the coax to the Icom IC-7000 and turned it on but did not hear anything there either.  I turned the IC-7000 off, switched the coax back to the FTM-400, turned it back on, and went back to work at my desk.  Around 8:30 PM the squelch started opening and I heard very faint voices way down in the noise.  After listening carefully I was able to determine that it was Steve (N8AR) running the net but I could not understand most of what was being said.

It was the first time in a long time that I had tried to participate in the net and I was disappointed that the new installation of the antenna on the tower and coax cables to the radios in the basement was not working adequately.  They were working OK when I tested them with Mike (W8XH) so it could have been an unusual band condition but Steve was obviously getting in from farther to the west than our QTH.  I enjoy operating and am looking forward to finally having our larger tower up and some HF antennas in operation but for now I need to concentrate on getting the VHF/UHF stuff working reliably (correctly and consistently).

I exchanged some e-mails with Gary at BCM regarding the magazine and then continued editing blog posts.  I got through the end of June by 11 PM and quit for the night.

2015/06/21 (N) Father’s Day

Leave a reply

Today was Father’s Day and also the summer solstice, which is the official start of the summer season.  Climatologically and culturally, at least in this part of Michigan, summer is more closely aligned with the period from Memorial Day weekend through Labor Day.  The summer solstice is, of course, the day with the most hours of daylight but it is not the day with the earliest sunrise nor the day with latest sunset.  Regardless of that detail, one of the things I like about this time of year is that the evening twilight lasts for a long time and fades to the blackness of night very slowly.  By contrast, the sun seems to set quickly in the winter and it gets dark very quickly after that.

Linda arranged for our son and daughter, and their families, to come over for brunch today.  It was a combination Father’s Day and happy birthday gathering as our daughter was out of town last week on her 34th birthday.  Linda spent last evening cooking, which minimized the amount of work required today.  I requested pie for Father’s Day and she found an excellent recipe for a vegan apple pie with a crumb topping.  She also made a dozen small chocolate birthday cupcakes.  The star of the show, however, was a Baked French Toast made with French bread and topped with streusel of ground pecans, cinnamon, brown sugar, and nutmeg with vegan “butter.”  It soaked overnight and all she had to do this morning was bake it.  She made a large bowl of fresh berries (strawberries, blueberries, and black and red raspberries) and sliced up some cantaloupe.

Company was due at 10 AM so I made a full pot of our Cafe Europe half-caff blend coffee.  We each had a cup and Linda transferred the rest of it to our insulated dispenser.  I was brewing a second pot when Meghan and Chris arrived around 9:45 AM followed by Brendan, Shawna, and Madeline around 10 AM.  Birthday and Father’s Day cards were exchanged but Madeline was the center of attention.  She pulled out her toy box and built a Lego tower with her aunt Meghan.  We walked around outside a bit, looked at the new roof and the cable entrance box, and played hide and seek in the backyard with Madeline doing the seeking, assisted by her mom.  I was hiding behind our gas grill, which had a cover on it.  Madeline saw my reflection in the rear door walls of the library, walked right past me towards the reflected image, turned away from my location, and was walking back towards Shawna before she spotted me.  Reflections are one of those things that we have to learn about.

The French Toast was done baking at 11 AM and we sat down to a fabulous brunch that included Prosecco and orange juice.  The Baked French Toast was outstanding and everyone had more than one piece.  By 12:30 PM no one was hungry for dessert so Linda packaged up four cupcakes for Meghan and Chris and four cupcakes for Brendan, Shawna, and Madeline along with a quarter of the pie for each group.  By 1 PM Madeline was showing signs of being tired, that being her normal nap time, so everyone gathered up their things and made their way to their cars.

After everyone had left we had some pie.  It was also outstanding, as good as any non-vegan pie I have ever had and, frankly, better than most.  Linda went for a walk while I settled in to finish the draft of yesterday’s blog post and start writing this one.  When Linda got back from her walk she read for a little while and then took a well-deserved nap.  By 4 PM I could not keep my eyes open and took a nap that lasted until 6 PM.  I have never been into “Hallmark Holidays” but I like Father’s Day.  🙂

For dinner Linda made a salad and reheated the last of the angel hair pasta and black beans and rice.  We each had one of the vegan cupcakes for dessert.

Today was my dad’s 90th birthday so after dinner I called to wish him a combined happy birthday and Father’s Day.  He did not answer, which is not unusual as without his hearing aids he doesn’t hear the phone ring.  I left him a voice message.

I have been busy enough with things the last two years that I have not read any of the magazines we receive as part of our various organizational memberships.  Tonight I went through the July 2015 issue of QST, the monthly publication of the American Radio Relay League (ARRL).  Although my main focus this summer is the remodeling of the interior of our motorcoach, I am trying to get ham radio antennas up and useable.  We are also trying to get a base built for the 70 foot tower we bought last summer, get the tower assembled and erected, and at least get some sort of HF wire antenna attached to it.

Linda was tired by 10 PM and trundled off to bed.  As a result of my nap I was not sleepy and stayed up using my iPad until well after midnight.

 

2015/02/01-05 (N-R) Another Month in Q

Leave a reply

2015/02/01 (N) Hola February

Yesterday would have been an excellent day to continue cleaning and waxing the outside of the bus—cool and cloudy without a lot of breeze—but it was also an excellent day for the inside computer work that we both needed/wanted to do.  I downloaded the free version of the Simple:Press forum WordPress plug-in the day before yesterday and was going to make a priority of installing it today on the FMCA Freethinkers website I have been developing until the activation of the Jetpack Site Management feature caused the admin panel (app) to crash.  We have had a problem for a while with one member who was unable (or unwilling) to interact appropriately online via our e-mail reflector.  The reflector does not require a login and does not have any way to moderate discussions or block/remove posts, so our options as a chapter were very limited.  A WordPress-based forum would give us all of those features.

I had an e-mail reply from support@ipower.com indicating that the Wordfence plugin had caused the problem.  They needed the answer to the security question in order to authenticate my support request and fix the problem. Bob Pelc provided me with that information which I supplied back to ipower.com.  Later in the day I got an e-mail indicating that the problem was resolved and I was, in fact, able to log in without any problems.  The e-mail said the Wordfence plugin had caused the crash and that they disabled it, but after I logged in it was still activated.  I did not, however, take the time to check if it was functioning correctly.  I also did not install the Simple:Press forum at this time.

For breakfast Linda improvised a potato tofu scramble with nutritional yeast, garlic, and other seasonings.  It was a hearty and flavorful start to the day.  After breakfast I called Jim A. back to discuss the FMCA seminar listing categorization document we have been working on.

I settled in to work at my computer on the consolidated blog post for November 10-16 while Linda settled in to work on accounting for the bakery.  She is also approaching the time of year when she has to pull tax returns together.  She uses Turbo Tax and needs an updated version each year.  The products she needed were on sale through Amazon Prime.  She purchased and download them, which also placed them in her Amazon software library, and they installed and opened without a hitch.

I got an e-mail from Harvey Carter (AC8NO), president of the South Lyon Area Amateur Radio Club (SLAARC), asking me to update the officer listing on the club website.  I took care of that and also changed that contact form (Contact Us page) to e-mail him instead of former president Mike Sharpe (WX8H).

By 2:30 PM I was tired of sitting in front of my computer so I changed into my work clothes and spent an hour trying to clean and wax a couple of windows on the bus.  The passenger side, which faces south, was so hot I cloud not touch it for very long, so I worked on the north side in the shade.

Jim/Flo L. and Jim/Barb B. disassembled the Select Comfort air mattress we had put in the park model trailer and divided up the parts.  We were going to donate it to the Salvation Army but did not get it done fast enough.  Jim B. would like the pump and controllers but Butch and Fonda need them to replace the defective unit on the mattress in their guest bedroom.  Since that is where I sleep when I am there, it is in my best interest to give it to them.

We invited all of our neighbors to come over for happy hour at 4 PM.  Barb B. came over with a glass of wine at 4:20 PM, so I poured a glass for Linda and me.  Jim B. was taking a nap as were Butch and Fonda.  (Hey; retirement is hard work!).   Butch and Fonda eventually shook the cobwebs out and came over.  Jim and Flo L. arrived but busied themselves with dinner preparations.  They were joining Jim/Barb B. for a belated Christmas dinner.  Jim B. eventually awoke and Barb left to join the other three for dinner.  Fonda left just before 6 PM to go to church but returned a few minutes later.  Apparently the evening service had been cancelled because of the Super Bowl.  She and Butch visited as the sun set and eventually it got chilly enough that we all decided to go inside.

I e-mailed Chuck Spera and my long-time friend John (J. C.) Armbruster earlier in the day but had not gotten responses from either of them by bedtime.  During the evening I had e-mails going back and forth with Steve Willey regarding the upcoming informal FMCA Freethinker gathering at the Liar Peg Leg Smith Monument boondocking area in Borrego Springs, California.  I also e-mailed Jim Ellmore regarding the same event.

A typical sunset in Quartzsite, Arizona.

A typical sunset in Quartzsite, Arizona as seen from our campsite on the north end of town.

2015/02/02 (M) Market Day

The last 24 hours have brought into focus why we are here for the winter.  It will be sunny and 80 degrees F today.  Detroit got 16.7 inches of snow from the storm that hit over the weekend, with 12 inches in Ann Arbor and similar amounts in Dexter, Howell, and Brighton.  When we checked this morning it was 7 degrees at home and going up to a high of 14.  Yeah, we are not missing that.

Breakfast was the bland store-bought bulk granola we have had to eat since running out of Linda’s homemade granola some weeks ago.  I wish we could carry a five-month supply of her granola; it’s that good.  Right after breakfast Linda started putting together menu ideas and a shopping list while I reviewed the latest seminar listing from Jim A. and e-mailed it back to him.  He called later to discuss it briefly.  I started working on yet another consolidated blog post for 17-23 Nov 2014 and did that until I could not stand to sit any longer.  The antidote for was go outside and work on cleaning and waxing the rear cap of the bus.

Butch and Fonda left around 9 AM and drove to Parker to go shopping at Wal-Mart.  Back home they shop at the Wal-Mart in Logansport and are familiar with the items there.  Not long after they left Linda drove to Blythe, California to do our grocery shopping for the week.  Of the supermarkets available to us we prefer the Albertson’s in Blythe, followed by the Smart & Final Extra at the same intersection.

Butch and Fonda returned from shopping and so did Jim and Barb.  Butch asked if I had ordered the coil for the MAC solenoid air valve that controls the a-c shutters behind the front bumper.  I hadn’t, so I took a break from cleaning and waxing the outside of the bus and called MAC Valve to order a replacement coil for the 111B601BAAA solenoid valve.  (I still have the old valve but I do not think I have it with us in the bus.)

Jim L. stopped by with some very fresh grapefruit and we got to talking about automotive detailing.  He recommended Finesse from 3M for polishing paint without leaving marks.  He said it works so well that the paint looks “wet” when you are done.  Butch had also suggested that I look at the Cyclo 5 dual head orbiting buffer/polisher.  Apparently this machine can finish paint with no swirl marks.

The FMCA Freethinker website /WP-admin/ panel was back up and running.  I logged in and checked the plugins.  They were all there but they had ALL been deactivated.  Tech support at ipower.com had indicated that they were going to disable the Wordfence plugin.  I re-activated most of them, but not all, and specifically did not re-activate the Jetpack plugin.  It is a large, feature rich plugin and the only thing I use is the Carousel feature to manage native WordPress image galleries.  Unfortunately I need that feature and have not found another plugin that does what I need.

I worked for most of the evening on the consolidated blog post.  By the time I finished it was too late to start selecting and editing photos, so I will do that tomorrow if I have time.

2015/03/03 (T) Wax On, Wax Off

I knew there was something else I was supposed to do yesterday, but I could not remember what it was.  I sometimes put “tasks” on my calendar, but that does not help if do not check it.  I remembered this morning what it was; I needed to call Sunset Sportswear in South Lyon, Michigan and follow up on an e-mail I sent last Thursday regarding our order for personalized SLAARC jackets.  I made that call and Pam took our credit card information.  Barb handles sales but had not made it in yet due to the snow.  Sunset Sportswear was closed yesterday because of the storm so if I had remembered to call them it would have been for naught.  Things often work out like that.

I also got an e-mail from the Escapees RV Club regarding the upcoming Escapade rally.  It indicated we could extend our stay until Sunday noon.  I called Lou Petkus, the head staff photographer for the Escapade, to let him know.  The rally ends on Thursday with normal departure on Friday and staff departure on Saturday.  Lou is trying to arrange a photography field trip for Saturday so the fact that anyone can stay until Sunday should help with participation.  I called the SKP headquarters and booked the extra night.

I confirmed which RV Park Lou and Val will be in on March 5th and I think we will try to get in there as well.  That location will position us close to the rally venue and allow us to caravan in together and park together.  (We have to be in by 11AM on the 6th.)  That, in turn, should make our staff photography work more convenient.  We plan to hang out (dry camp) with RVillage founder Curtis Coleman for a couple of nights before this at his rental home near Casa Grande, which will put us a lot closer to Tucson than we are here in Quartzsite.

We had also mentioned to Lou and Val at Quartzfest that we were thinking of heading to Organ Pipe Cactus National Monument after the Escapade.  They had been discussing it and decided they would like to go there as well so we will probably caravan there with them.  After OPCNM we plan to head to Big Bend NP (BBNP) in Texas and Lou and Val would also like to go there.  That is a three day drive for us, and we may take six or seven days to get there depending on where we might stop and what there is to see long the way.  Whether we travel together or separate will be determined later.  Our friend, Mara, and another women from the WINs are also headed to BBNP sometime in March and we have tentatively agreed to meet up with them if we can work out the timing.

I checked my e-mail and had a reply from Jetpack tech support at WordPress.com. “Happiness Engineer” Jeremy said that Wordfence has been known to cause issues with the Jetpack plugin.  He acknowledged that Wordfence is a powerful and important plugin but can be very aggressive in protecting websites.  Given that Wordfence appears to have caused the crash of the FMCAA Freethinkers WordPress /WP-admin/ Jeremy said I probably did not need to reinstall the Jetpack plugin.  I filled out a support ticket yesterday for this issue on the Wordfence website as I have a premium (paid) membership.  They acknowledged the support ticket right away but an actual response will likely take longer.

I had all of these communications chores done by 11 AM and decided to continue cleaning and waxing the outside of the bus.  I started with the rear, as it was still in the shade, and finished the lower half.  It was tedious as that is the engine hatch and it has numerous horizontal indentations that run the full width.  These indentations are open on the inside top for airflow and have screens to keep things from getting in (like fingers).

Another view of the sunset from our campsite in Quartzsite, AZ.

Another view of the sunset from our campsite in Quartzsite, AZ.

I continued on around to the driver side of the bus which faces north.  The temperature this afternoon got up to 80 degrees F, and it was very hot in the sun, but it was pleasantly cool in the shade of the bus.  It was near perfect conditions for the work I was doing.  I worked most of the afternoon and did not quite get the back half of the bus cleaned and waxed.  A couple of bay doors and I will be past the half way point on that side.

I am going to try to work on this at least a few hours every day, otherwise it will never get done and this is an ideal place to work on it as long as I am not working in the sun.  The south facing passenger side is going to be more of a challenge and I will have to limit my work to the morning before the body panels heat up.

UPS showed up today with my coil for the MAC valve which turned out to be an entire new valve.  Rather than try to remove the solenoid coil I may just install the whole valve.  UPS also brought Fonda’s new sewing machine.  It only weighs 13 pounds.

Butch got back from a rock hunting field trip late in the afternoon and we stood around chatting as an amazing sunset developed around us.  As I have mentioned before, sunsets here are often 360 degree events and this one surrounded us with color before finally fading into another starry night.

Linda made a wonderful dish for dinner last night and we had it again this evening.  She pan-grilled polenta and served it on a bed of dark leafy greens topped with puttanesca sauce made from scratch.

After dinner I selected photographs for my November 17 – 23, 2014 blog post and processed them.  I uploaded the text to our WordPress site and then uploaded, captioned, and integrated each photo in turn.  I also had to enter all of the tags, which I figure out as I read through the post.  If there is one thing I would like to have at this point it is the ability to highlight key words and phrases in my Word document and have them automatically become tags when the text is uploaded.

By the time I published the post and went to bed to finish this one it was midnight.  At eight minutes after midnight MST I was one hour into my 63rd year as I was born on this date at 00:08 in the Central Time Zone, where eight minutes past midnight happened an hour ago.

2015/02/04 (W) 63 and Counting

I finished my blog post for yesterday late last night and e-mailed it to myself at eight minutes after midnight, the hour and minute of my birth, or so I have always been told.  Linda and the cats were all asleep and I observed the moment in quiet solitude.  As I noted at the end of yesterday’s post I was actually an hour late in my observance as we are currently in the Mountain Time Zone and I was born in the Central Time Zone.  But it was the thought that counted.

Sixty-three is not a milestone birthday anniversary, other than making it that far.  On my 60th birthday I became eligible to retire, and did so four months later.  On my 62nd birthday I became eligible to start drawing social security, but didn’t.  On my 65th birthday I will become eligible for Medicare.  The year I turn 66 Linda will apply for Social Security benefits and immediately suspend them.  I will be eligible for my full Social Security benefit but will not apply for it.  I will apply for the spousal benefit instead.  Our monthly Social Security benefits continue to increase by 8% per year until age 70, a solid and guaranteed return, so Linda will start taking her benefits then and I will file for, and take, my benefits when I turn 70.

Having thought through the complexities of birthdays, we had breakfast and then I got to work cleaning and waxing the outside of the bus.  My plan was to finish the driver side but not spend all day at it.  As it turned out, I spent most of the day at it, taking breaks to check e-mail.  It is just slow work, especially since so much of it has to be done on a step ladder.  I have no idea how many trips I made up and down that ladder, but it was a lot.  It is only a seven foot step ladder so I have to stand near the top to reach the top of the sides which are over 12 feet from the ground.  I cannot reach very far to the side either, so I work from one side of the ladder then climb down and climb up the other side and work from there.  I then climb down and move the ladder about three feet and do it all again; over, and over, and over.  But as Long as I keep going it eventually gets done.  I am, however, seriously considering getting a Cyclo 5 dual head orbiting buffer/polisher.  There is simply too much bus to do this by hand.  I am also considering getting a platform to put between two ladders and/or a four-wheel elevated work platform to use in the barn if/when we get it built.

I got a call from our daughter wishing me a happy birthday and had a nice chat with her.  I asked if Katie had made a final college selection but she is not done with interviews yet.  Perhaps we will know in a few weeks where she is headed in the fall.

Yesterday Linda invited all of our camping neighbors to come over today at 4 PM for happy hour to celebrate my birthday.  In preparation she spent part of the day making cupcakes with chocolate frosting.  When she wasn’t cooking she did accounting and tax return work for Butch and Fonda.  Around 3 PM she prepared bruschetta using what was left of a loaf of Barry’s Basic Bread and the puttanesca sauce she made a couple of nights ago.  Larry/Sandy, Jim/Barb, and Butch/Fonda all brought chairs and beverages of their choice.  Butch and Fonda brought chips, salsa, and hummus and the peanut and dried fruit mix they make.  We sat around talking until the sun set at which point the air temperature cooled off and we all retreated to our rigs.

I got a call from our son during our happy hour and excused myself for a few minutes to chat with him.  It was 7:40 PM back in Ann Arbor and Madeline was getting ready for bed.  I got to “chat” with her and she wished me a happy birthday.  With encouragement from her mom she asked me “How is Arizona?”  I told her it was very nice here.

We skipped lunch today and did not have dinner because we filled up on happy hour snacks.  Linda played online word games while I started assembling the consolidated blog post for November 24 – 30.  She turned on the MiFi and trundled off to bed to watch an episode of Downton Abby on her iPad.  I finished editing the post and selected two photos to go with it.  When I checked I found that I did not have photos for most of the days covered by the post.  I thought about uploading it but decided against it as it still takes time to upload the text, upload and insert the pictures, and create all of the tags and I was too tired to maintain the needed concentration.  Somewhere in there I read through a reply from Chuck Spera and sent him the next volley in our e-mail conversation.

Overall it was a good 63rd birthday.  Given our winter travel lifestyle I face the interesting prospect of celebrating my birthday somewhere different every year for many years to come.

Our fellow campers gathered by our bus for my 63rd birthday happy hour. L-2-R: Sandy, Larry, Barb, Jim, Butch, Fonda, me. Photo by Linda (not shown).

Our fellow campers gathered by our bus for my 63rd birthday happy hour. L-2-R: Sandy, Larry, Barb, Jim, Butch, Fonda, me. Photo by Linda (not shown).

2015/02/05 (R) A Screwy Tire

The overnight lows are now dropping into the upper 40’s at night and the coach cools off just enough that I turn the heat on in the front of the bus while I make coffee in the morning.  Soon enough the sun starts heating up the coach and we are pulling the accordion shades down to keep it out and opening windows and turning on ceiling exhaust fans to draw cool air in.  A couple of days ago we finally put the awnings out on the south facing passenger side of the coach.  Between the patio awning and the bedroom awning they shade more than half of the upper portion of the coach and help keep the interior temperatures in check.  We have not had them out much, however, because of the somewhat persistent winds in the La Paz Valley.

After breakfast I wanted to setup the TireTraker TT-400C TPMS.  Once I started I would need to install the sensors on all 13 tires.  In order to install the sensor on the spare tire in the car I had to empty out the back so I could get to the tire.  Linda was helping me and noticed a screw in the passenger side rear tire.  It was right at the edge of the tread but not technically in the side wall.  The tire was holding pressure but when I started to back the screw out it started to hiss so I screwed it back in.  Nuts.

Linda got online to look for tire repair shops in Quartzsite.  The first three numbers we tried were out of service and the Love’s Truck Stop only repaired big tires, not small ones, so I called Jim Liebherr to see if he knew of some place in town.  Flo answered the phone and could not locate Jim so I asked for a return phone call.  Butch then offered to drive me downtown where he thought he remembered seeing a tire shop.  As we were pulling out of our camp it occurred to Butch that the RV Pit Stop, just south of us on Central Avenue, might do tire repairs.  Before we even got that far we saw the sign for Best Auto and Tires.  We have walked or driven past this place dozens of times but never paid any attention to the fact they sold and serviced tires.  At the time we did not care.

They said they would have to see the tire so we drove back to camp and I drove back in the car.  They said they could repair it properly with an internal patch and they would get right on it if I wanted to wait for it.  $14.  Deal.  I could easily have walked back to camp from there but I was back with the car within an hour.  If the tire had not been repairable we would have had to take it off the car and use Butch’s Chevy Suburban to drive it to Yuma or Lake Havasu City where there are Discount Tire Locations.

Jim L. returned my earlier phone call while I was waiting for the tire.  He and Flo use a dentist in Los Algodones, Mexico and are very satisfied with the service and price.  I have a tooth that is bothering me just a bit and was giving some serious consideration to making an appointment with someone in Los Algodones.

I installed the batteries in our new TT-400C sensors and programmed the baseline pressures into the monitor (receiver).  I then installed the sensors on the bus and car tires, linking each one to the monitor as I went.  Programming the baseline pressures first is the easier way to install the system.  In setup mode the monitor displays each tire position in turn.  While the position is displayed a sensor is screwed onto the valve stem.  The application of pressure to the sensor “wakes it up.”  When the sensor starts transmitting the monitor associates it with the displayed tire position.  After exiting setup mode only the programmed tire positions display on the monitor.

In addition to the overall setup procedure there are several things I like better about the TT-400C system compared to the PressurePro system we have had since the 2008 FMCA national rally in St. Paul, Minnesota.  A major one is that the baseline pressures are programmed into the monitor.  On the PP-TPMS the baseline pressures are determined by the pressure in the tire at the time the sensor is put on.  Another thing I like is that the TT-TPMS monitor is powered by rechargeable batteries and is not plugged in when in use.  That makes it much more convenient to move it between the bus and the car, but especially to carry it around while installing and associating the sensors to wheel positions.  Finally, I like the sensors, which are much smaller and only weigh 0.4 ounces each.

Linda helped me reload the back of the Element and sort through all of the “stuff” that was “stuffed” in the glove box and the passenger side dashboard trays.  (When was the last time someone actually stored gloves in an automotive glove box?).  With everything sorted out and repackaged in ZipLock bags I stored it back in the glove box and locked up the car.

Linda spent part the morning working on accounting and tax returns for Butch and Fonda and talking on the phone to Dave, the controller at Metropolitan Baking.  I got a call later from Jim Ammenheiser and then did a final proofreading of our Education Committee recommendation to FMCA staff for how to restructure the categorization and listing of seminars and activities in the national rally programs.

We took a break and had the last two cupcakes from yesterday with some vegan Mocha Almond Fudge coconut “ice cream.”  We were supposed to have these last night for my birthday but we were not hungry after snacking at the happy hour birthday gathering.  Linda then went for a walk.  Linda got me a birthday card and a towel with an elastic edged hole for my head.  I tend to get food on my shirts when I eat and the towel is basically an adult bib that can be easily laundered.

Our fresh water tank was a bottle cap shy of empty so I filled it.  It usually takes about 50 minutes to fill the tank starting from empty so I set the timer on my smartphone for 40 minutes.  When it signaled me to check on the progress the tank was already overflowing.  (It has a vent tube on top of the tank that runs through the floor of the bay.)  I don’t think I wasted more than a few gallons of soft water so it should not throw my water usage and softening calculations off by much.  The good news was that the post-fill hardness test showed the water coming out of the softener at 0.0 to 0.5 gpg total hardness (0 to 10 ppm.)  That was better than the reading I got right after I recharged the softener, so perhaps it still had some residual salt in it initially.

At 4 PM I was getting ready to upload a blog post when the UPS truck showed up and dropped off two boxes for me.  It was the Chemical Guys microfiber products I had ordered recently, including two microfiber auto detailing aprons.  Butch returned a few minutes later with a small package for me.  It was the lens hood I had ordered for my Sony zoom lens and it had been mailed USPS.  He also had eight (8) Full River 6V L16 AGM batteries.  I helped him unload them from the Suburban onto the concrete pad on the driver side of their bus.  Fonda emptied out the driver’s side of their battery bay and she and I then moved the batteries to the bay where Butch positioned them.  He left them in their boxes and will install them when they get back to Twelve Mile.

At 5:15 PM I finally got around to uploading the consolidated blog post for the last week of November (2014).  I then started thinking about what to do with my December 2014 posts.  As of today I am still 67 posts behind and putting up daily posts is not realistic.  In looking through my photos I was surprised to find that I took very few from the time we left the house until we arrived in Quartzsite.  I decided to do consolidated posts for Dec 1 – 4 (Twelve Mike, IN to Alvarado, TX), 5 – 8 (visit with Donn Barnes), and 9 – 12 (travel from Alvarado to Quartzsite, AZ).  I have more pictures for the rest of the month, so I will have to figure out what makes sense.  I compiled the posts for December 1 – 4, selected and processed one photo, uploaded it, selected the categories, and entered all of the tags.  I posted it and then realized I wanted to edit the URLs slightly so I logged back in and found that I was unable to type anything.

It took me a while to figure out that the problem was the built-in keyboard on my ASUS G750JM ROG notebook computer.  I got it at the end of April last year, so I have only had it for eight months.  I decided to run a full scan using ESET Smart Security since I could do that with just a mouse and the Bluetooth mouse was working just fine.  It found 18 threats and dealt with 16 of them.  I then ran CCleaner, after which I enabled the onscreen keyboard.  Although intended for use on touchscreen computers, at least I could type things into a search box using my mouse.

I found some references to similar problems on answers.microsoft.com with the suggestion to examine the keyboard device properties.  If it indicated the device was installed and working correctly it was probably not a Windows 8.1 problem.  The other suggestion was to try an external keyboard.  If that worked it would confirm a keyboard hardware problem.  I had already gotten my Gigaware wireless keyboard out so I plugged in the USB dongle, turned on the keyboard, and voilà, I could type again!

Another post on the Windows forum listed website links for ASUS support so I started following those.  One ASUS website wanted the serial number of my computer, which I had to get off of a tag on the bottom of the case with really small type.  Once I had that entered correctly I was able to go to a download page with 81 files available, including bios and chipset code.  There were two files that seemed to have something to do with the keyboard.  By 1:15 AM I had a half dozen tabs open in two different browsers with no definitive understanding of what had happened or what to do to fix it.  I then realized that the Shift Lock key on the keyboard was illuminated and I could toggle it on and off.  I could also toggle the Number Lock, so I tried typing and the keyboard was working once again.  That, however, did not give me any confidence that it would continue to do so.  I decided I was not going to shut the computer down for fear of not being able to log back in on startup.  I was not about to start downloading and installing anything at that hour so I went to bed tired, annoyed, and, frankly, a bit discouraged by this unwelcomed turn of events.

 

2014/06/19 (R) Visitors

Leave a reply

We got to visit several times with John and Marian Hagan while we were in Florida this past winter.  They were members of our FMCA Freethinkers chapter until they decided to stop full-timing, bought a house in Dunnellon, Florida, put their motorhome up for sale, and did not renew their FMCA membership, which meant they could no longer be members of any FMCA chapters.  But we had established contact with them by the time all of that transpired and as Dunnellon was only 25 miles south of Williston, it was easy to meet up with them, which we did on several occasions.

John has a daughter who lives in Ypsilanti, Michigan and she has twin 4-year olds, so he and Marian had indicated that they would be visiting them sometime in June.  I e-mailed John as soon as we got back from the GLAMARAMA rally to check on their status and found out that they had arrived in Michigan about the time we left for the rally.  They were planning on staying for several more weeks, but we invited them to come to our house for dinner and a visit as soon as mutually possible.  That turned out to be today!

We had cloudy skies leftover from the storms of the day before but no additional rain.  John and Marian arrived mid-afternoon and stayed until almost 9 PM.  We had a good, wide-ranging chat and enjoyed a nice meal of mixed greens salad, lentil loaf, baked potatoes, and roasted asparagus.  We had the Franzia Sweet Red wine with dinner and capped off the meal with fresh strawberries, Lotus Biscoff cookies (the same ones they serve on the airliners), and our Sweet Seattle Dreams 1/2 caff custom coffee blend from Teeko’s in Howell.

Since John and Marian are in the area for an extended period of time, they have been visiting a lot of local attractions, especially things connected with the University of Michigan in Ann Arbor.  We all agreed that we would get together at least one more time while they are here, perhaps meeting them in the Ann Arbor / Ypsilanti area and dining at a local restaurant.

 

2014/06/17 (T) Oral Tradition

Leave a reply

We had dentist appointments this morning…in Dearborn.  That’s 50+ miles from where we now live, and we try to schedule our appointments to avoid the rush hours at the beginning and end of the workday.  We had 11:00 AM appointments about a month ago but had to reschedule because we were both ill.  The next available appointments (together) were today at 9:30 and 10:30 AM.  We had to leave the house at 8:00 AM which put us in the late morning rush.  (The morning rush starts by 7:00 AM and usually thins out by 9:00 AM unless there is an accident or really bad weather-related road conditions.)  From where we live if we need to head into the Detroit metropolis we try to leave by 6:30 AM or wait until 9:00 AM if possible.  Unfortunately that is not practical or possible if we need to be somewhere between 8:30 and 9:30 AM.

We were both scheduled for the same procedures involving work on multiple teeth.  Unfortunately Linda developed a problem with a tooth during the rally last week and needed that looked at first.  It turned out that she broke a molar that was mostly filling and will need a crown.  She goes back next week for the prep and then has to return at least three weeks after that for the crown plus all of the work she was supposed to have done today.  The purpose of plans is so we have something to do each day in case nothing else presents itself, which it almost always does.

We did not eat breakfast before our appointments and had to wait for the local anesthetic to wear off afterwards before we could eat.  We did not accomplish much beyond our appointments other than some time spent at our desks.  We had “lunner” (or “linner”) around 3:00 PM and vegan cupcakes with strawberries around 6:30 PM.

At 7:00 PM (EDT) we participated in an RVillage webinar for prospective RVillage Ambassadors.  We were already approved for this role based on our interactions with Curtis Coleman, the founder and CEO of RVillage and the RV Friend Network, but wanted to participate like everyone else.  Curtis, along with Hillary Murray, were online for an hour and 20 minutes explaining the “why, what, and how” of the ambassador program.  Hillary will run the program and be our main point of contact.  After the webinar we turned in early and watched an episode of Doc Martin from season two.

2014/06/15 Family Time

Leave a reply

We were parked in a fenced compound area next to the regular “campground” at the Elkhart County 4-H Fairgrounds.  The campground has gravel sites with 50A full hookups, and we were allowed/encouraged to use the sewer connections to dump our holding tanks before departing this morning.  We had checked out the campground last night and decided that it would be easier for us to pull around to the dump stations on the outer road than to maneuver into and out of one of the open campground sites, all of which were back-ins.

I have mentioned before what a nice facility this is.  Several of our GLCC members are from north central Indiana and explained to us that the fairground is as nice as it is because it is booked every week for most of the year, winter being the exception.  Elkhart is considered the center of the RV industry in the U.S., but the reality is that RV-related industry is located throughout north central Indiana, and a little bit of southern Michigan, with a few facilities in other parts of Indiana and Ohio.  There is also significant RV industry in California, Oregon, and Florida, and to a lesser extent in Pennsylvania and Alabama.  By “RV Industry” I am referring to manufacturing, not RV parks, resorts and campgrounds, or RV dealers and service facilities, which are obviously located all over the place.

We skipped breakfast and coffee, as we always do on travel days.  Linda prepared the inside for travel and then we visited for a while with our GLCC friends.  Around 9:00 AM I unplugged the electrical power, stowed the cord, turned on the chassis batteries, opened the air valve for the engine accessories, and fired up the engine.  I did not have any trouble getting out of our parking spot or the compound.  I drove over to the dump station, which can accommodate nine RVs at one time, and Linda followed in the car.  While the holding tanks were emptying we hooked up the car for towing.  With everything stowed and secured for travel we checked the toad controls and lights and were on our way, exiting the fairgrounds at 9:25 AM.

We followed the same route home that we used when we left the Escapade rally a month ago: CR-34 (Monroe St.) east to CR-29 north to IN-4 east to IN-13 north to US-20 east to I-69 north to I-96 east to M-59 east and finally a couple of miles of dirt roads to our house.  We stopped at the Travel America (T/A) truck stop on M-60 at I-69 to put biocide and Stanadyne diesel additive in the tank along with 75 gallons of diesel fuel.

We had just over 1/4 tank of fuel indicated on the fuel gauge when we pulled in to the T/A.  If the gauge is anywhere near accurate that was approximately 50 gallons of fuel, enough to travel another 200 miles and still have 15 – 20 gallons in the tank; more than enough to get us to the Mobil truck stop on I-96 about 25 miles before our house.  I wanted to use as much of the fuel in the tank as I could before adding more but did not want to risk running out or sucking sediment off the bottom and clogging the fuel filters.  In the end we decided it was safer to stop and add fuel while we still had the 1/4 tank.  The 75 gallons brought the fuel gauge up to 5/8ths, which is what I expected.  The fuel tank capacity is 235 gallons, but I assume the full mark on the gauge corresponds to 200 gallons.  That makes every 1/8 of a tank on the gauge correspond to 25 gallons.  We also presume that our average fuel economy, based on prior data, is 6 MPG which equates to 150 miles per 1/8 tank.

We did not fill the tank because the bus is going to be sitting for a while and we did not want to have all of that fuel onboard aging in the summer heat.  There is a reason, however, to keep the fuel tank as full as possible.  Most of the fuel that is pumped to the engine is used to cool the injectors and the DDEC engine computer and returned to the tank. The more fuel in the tank, the less frequently any particular molecule passes through the engine giving the fuel in the tank more time to dissipate the heat.

Our trip was easy and un-eventful other than the powered driver-side windshield shade quite working.  Add that to the list.  We got home by 1:30 PM which gave us time to unload food and a few essentials from the bus and take showers.  Since Linda spent Saturday morning preparing food, she only had minimal cooking to do for dinner.  Our son, daughter-in-law, and grand-daughter arrived at 3:30 PM and our daughter and son-in-law arrived at 4:00 PM.  Madeline had a cold, wasn’t feeling well, and had only had a short nap, but she was fine as long as she was busy.  This was a combination birthday and Father’s Day gathering, but mostly an excuse to gather our small, immediate family.  We had a lovely summer meal of potato salad, collard greens cole slaw, baked beans, and cheeseburgers with chocolate cupcakes (from a local bakery) and fresh strawberries for dessert.  All vegan, and all delicious.

Brendan, Shawna, and Madeline left shortly after dinner and Meghan and Chris left around 8:00 PM.  Although our morning departure and drive home had been quite routine and the family gathering had been relaxed and relatively easy, it all added up to a long day.  I started the download of an update to my Adobe Creative Cloud subscription that looked like it was going to take a while, so we skipped watching an Episode of Doc Martin and turned in for the night.