Tag Archives: Escapade

2014/05/03 (S) Ham It Up

Today started with breakfast out and felt like we were finally starting to get back into the flow.  We drove to South Lyon for the Saturday morning breakfast gathering of our South Lyon Area Amateur Radio Club, as we do almost every Saturday morning when we at the house.  Steve (N8AR) gave me a lead on someone who might be willing to build our pole barn.  After breakfast we returned home and I walked Linda through the project I discussed yesterday with Steve for redoing the rear basement walkout retaining walls, drainage, and yard grading.

I worked on our blog and Linda worked on lunch preparations while we awaited the arrival of our daughter and son-in-law.  They have had Linda’s Honda Civic Hybrid since December and were returning it, so they drove two cars.  Linda got to visit with them in late February / early March, but I had not seen them since mid December.  We had a nice lunch of mixed greens salad and vegan Sloppy Joe’s with sweet gherkin pickles on the side.  Fresh strawberries and carrot cake cookies provided a sweet ending to the meal.  We had a nice visit.

Steve from Village Landscaping Development stopped by with a brochure, business card, and the project proposal written up on a more official estimating form.  We will take a few days to think about, but it’s a very good proposal and I am 99% certain we will hire him to do this work.  It would be nice to get it done in late May to early June, between The SKP Escapade and the GLAMARAMA rallies, but it may not be dry enough by then.  If not, it will have to wait until early July after we return from the installation ceremonies for Linda’s sister who is assuming one of the top leadership positions in the St. Louis Province of the Congregation (Sisters) of St. Joseph.

A little later Phil Jarrel, from Best Precision Grading, came by to take a second look at the site preparation and grading work for the pole barn.  We walked the site and agreed that I could/should change the orientation of the building just a bit from where it is currently staked.  We also discussed how to make sure the barn was located behind the front line of the house and talked through the permitting and construction process.  He did not have any builders to recommend, but he did recommend a concrete contractor for the pit and floor.

We did quite a few construction projects at the previous house over the years but the pole barn involves elements that are new to me, and I now have to deal with a Township for a land use permit and the County for building and grading permits.  I am fairly set on the size, location, and basic design/materials, but we not have settled on a builder or materials supplier.  Consequently, we still do not have an accurate total cost estimate.  Until everything is in place, and the cost is known, nothing can move forward.  Meanwhile, the days keep flipping over on the calendar.

 

2013_07_03 (Wed) Escapade Day 4, Winding Up, Winding Down

Today was the 2nd to last day of the 53rd Escapade / 35th anniversary celebration of The Escapees RV Club, and the last day for the inside vendor booths.  There were seminars scheduled all day, but we decided to stay at our rig and work.  I edited draft blog posts and finally uploaded my first one.  I also added a picture to our home page, although not exactly where I wanted it, so I removed it.  Linda worked on our personal accounting and additional arrangements related to the sale of our old house.  We were unable to find a charitable recipient for our Yamaha E-50 electronic organ, so our daughter is taking care of having it moved to the new house prior to the closing date for the old house.

We walked over to the Wyoming Center and signed up to have our black and grey tans hydro-cleaned by All Pro Water-Flow on Fri morning at 8 AM.  We then went to The Row party to check on our ham radio BOF friends who were setting up a special event station and any other BOFs that were there.

Having exhausted those possibilities we went back to our rig, had a bite of lunch, and continued our computer and accounting work.  It was warm this afternoon, with a forecasted high of 91 degrees F (which we hit), so we closed up the coach and turned on the air-conditioners.

We got a late start for the 4:30 PM HFH C-BOF business meeting and social, so we accepted a ride on one of the many golf carts that transport Escapade attendees between the various campgrounds and the activity buildings.  The HFH C-BOF membership has fallen way below minimums and those present voted to de-certify and continue as a regular BOF until April 2015.  A new treasurer was elected, so the funds will remain with the HFH BOF.  The Bylaws and standing rules are technically no longer valid and will be re-vamped as standard operating procedures.  It appeared that current President Steven Gullette will take care of that and continue as the “leader” of the BOF.  There were 13 members present and they all stayed for the social.  We managed to find enough snacks to get partially filled up, so we had a light dinner before going to our 7 PM Freethinker gathering.

It was still warm at 7 PM, so our Freethinkers group met inside VJ and Carol’s Fleetwood Bounder at Boxelder RV Park (which turned out to only be 7 RVs up from us).  They had the air-conditioning turned on and it was very comfortable inside.  Besides the hosts and us, Jerry Stauffer and Marc Matheson were there.  It turned out that Mark is a ham (KD6KR) and Jerry is a former ham.  Mark had to leave to watch a friend in the talent show, but we all enjoyed his company while he was there.  Consistent with our prior experiences meeting up with Freethinker RVers, we had a wide-ranging, enjoyable conversation, fueled by some wine and snacks.

 

2013_07_01 (Mon) The 53rd Escapade, Day 2

We attended two seminars this morning, both by Shawn Loring.  One was on Investing For RVers and the other was on Domicile and Estate Planning issues.  Shawn is an attorney licensed to practice in TX and CA, as well as a licensed financial planner.  He resides in Livingston, Texas and is the corporate attorney for The Escapees RV Club.  He is also a member of the CARE Board of Directors.  Both presentations were standing room only and were excellent, providing good overviews of the topics with considerable depth at selected points.

I mentioned yesterday that we had picked up literature and an application form for the B. P. O. Elks because they are letting SKPs attending Escapade to join the local Gillette chapter.  After reading through their Guidebook For Members last night, we decided that the Elks where not a good fit for us.  Not having access to camping at Elk Lodges does not diminish our RVing experience in any way, and it seems to me that joining only for access to overnight RV parking is hardly in the spirit of the Elks organization.

We took a pass on the afternoon seminars and did some grocery shopping instead.  When we got back we had a card in our door handle from Black Hills Pro Wash.  We thought it was a reminder about our appointment at 8:00 AM tomorrow to have our rig washed.  A bit later, however, I got a call from Trevin informing me that they would not be able to clean our rig, or anybody else’s, as the Escapade had given exclusive washing rights to All-Brite.  In spite of Pro Wash having tried to register as a vendor, and being more than willing to pay the Escapade vendor fee, they were denied.  There are multiple vendors here selling things like LED light bulbs, and there are more rigs here than one company could wash, so having an exclusive arrangement with one company only served to penalize attendees, especially if they did not want to use the sole source vendor.  Limiting my choices does me a disservice as a member of the club.

We went over to the Wyoming Center at 7:00 PM for the nightly door prize drawing.  The Escapade was successful in obtaining a lot of door prizes from rally vendors and local merchants, and the drawing went on for 45 minutes.

Ventriloquist Patty Davidson performed.  She is very talented, but the acoustics of Spirit Hall in the Wyoming Center were not adequate for what she does and it was difficult to understand much of what she (and the dummies) said.  She did the old Abbott & Costello “Who’s on first?” routine with two dummies, and it was impressive.  She also had her brother-in-law, a singer/song-writer/guitarist, perform between sets.  He was also very good, and better suited to the acoustics of the venue.

 

2013_06_29 (Sat) Anticipation, Registration, and Relaxation

I got up a little before 5 AM and watched the sun rise.  There were low clouds to the NE that provided color, and the orb broke the horizon at ~5:25 AM.  But I wasn’t the first person up in the campground; someone was walking two dogs as the sun rose.  RVers seem to come in two basic types: 1) up before the sun, and 2) party into the night, although type 1 seems to be much more common at large RV rallies.

Escapade registration opened at 9:00 AM today along with the SKP (pronounce each letter “Es” “Kay” “Pees” and you get “Escapees”) store.  We were there at 9 AM as we wanted to shop for SKP/Escapade shirts and were told yesterday that they tend to sell out fast.  (These are event specific shirts.)  They did not have any shirts with pockets (apparently they had to be pre-ordered), and they did not have any men’s medium size.  I bought a men’s large and Linda got a women’s medium.  (Apparently RVers only come in two sizes, large and small.  We had the same problem with clothing at the FMCA store.)  We got some free coffee and sat in the “WiFi Cafe” area to look at the program and other materials we received in our registration bag.  Charles and Connie Martin showed up about 20 minutes later and the men’s shirts were already sold out.  Rick showed up shortly after that and joined us.  While I can understand the Club not wanting to be stuck with unsold event-specific merchandise, the lack of available inventory was simply baffling.  They were sold out in the first 30 minutes, and there would still be people arriving today and tomorrow!  The other baffling thing is that they did not have generic Escapees RV Club shirts for sale.  ???

By the time we got back to the coach it was pushing noon.  We gathered up a load of laundry and supplies, and then took a minute to have a light lunch before heading out.  We drove to “Surf-N-Suds”, Linda’s laundromat of choice in Gillette.  Linda stayed to do the laundry while I ran some errands.  I got back as she was finishing up and helped her fold the laundry.

When we got back to our coach John & Cheryl were sitting outside under their patio awning, so we brought our chairs over and joined them, the first chance we’d had to do this. The couple behind us (he is the FMCA INTO area treasurer) joined the conversation, and we all had a good, long chat.  Both couples are full-timers, and there is always something to learn in such conversations.

Eventually we broke for dinner, after which we went for our usual evening walk.  This time we chose a route that avoided RVs as much as possible (so we could actually go for a walk).  SKPs are very friendly, and passing anywhere near their rigs usually leads to a conversation.  We enjoy these interactions, but they interfere with walking, so we have to be conscious of our intent.

When we got back to the coach we sat outside for a while and had a nice chat with Rick.  As I have mentioned before, it cools off quickly here in the evening and this was no exception.  A little quiet time and a glass of Lawrence Elk Black Currant wine from Prairie Berry Winery, and it was off to bed.

 

2013_06_27 (Thu) Cowgirl Barrel Racing

Today was the first early entry date for the Escapade, and RVs started rolling into Boxelder RV Park at 8 AM.  The parking crews were ready and waiting and directed the rigs to their assigned areas and got them parked with great efficiency.  Lynn & Linda Laymon were working the area near where we are parked, and I recognized their names from the roster for the Habitat For Humanity build we will be doing in Sheridan in July.  We had a nice get-acquainted chat that Linda joined when she returned from her morning walk.  (We have been walking together after dinner each evening, but Linda likes to do a 4 – 5 mile power walk in the morning, and I figure that’s an opportunity for each of us to have a little “me” time.  We are, after all, living in a 300 sq. ft. condo on wheels with a really big “yard”.)  In the course of the conversation we realized that the shift from FMCA to SKP had occurred and we got out our SKP name tags and pinned them on.

We enjoy being members of both FMCA and The Escapees RV Club, but they are different.  FMCA is larger and has an extensive volunteer governance and management structure, as well as a paid staff.  Membership is restricted to motorhomes, but it has a fair number of members and chapters focused on bus conversions, so it’s a good fit for us.  The Escapee RV Club is smaller, and is actually a privately owned family business.  There are no restrictions on what kind of RV you own, and there is a much stronger focus on full-time RVing.  The club was founded by Kay and Joe Peterson as a support group for full-time RVers.  They were living in a trailer and raising a family at a time when that was not “fashionable” as Joe was an itinerant electrician.  I have heard it said more than once that “You belong to FMCA, but you are an Escapee.”  Based on our limited experience, that rings true.

I was reminded this morning that “someone” has a birthday on the 30th of this month and that they would like to be taken out to dinner, “or something.”  I accepted the “heads up” as a friendly but necessary reminder as I do get preoccupied at times and forget things, even important things like “someone’s” birthday.  Plus, the 30th is the opening day of the Escapade, so the activity level will ratchet up quite a bit and I could certainly be distracted by that.  An online search of local restaurant menus, however, failed to reveal anything other than a deli with a couple of vegetarian sandwiches that could be made vegan by leaving off cheese, mayo, and any other animal products that might normally be included.  Not exactly a gourmet birthday meal, but at least “someone” wouldn’t have to prepare it.

We were on tap for another warm day, but decided to leave the windows open and the vent fans on as long as possible.  Although we have a good 50 A electrical connection here at the CAM-PLEX, we like fresh air, and the house air-conditioners are rather noisy so we prefer not to use them if possible.

We spent the late morning and most of the afternoon working at our computers.  I worked on my draft blog posts while Linda worked on our personal accounting.  We had the vent fans going and some small fans to move air around, and I was surprisingly comfortable in spite of the interior temperature climbing past 88 degrees F.  Linda usually tolerates (likes) heat much better than I do, but wasn’t feeling 100%, so mid-afternoon we finally turned the air-conditioners on and brought the temperature back into the mid-70s.  (BTW:  Because of the surface area to volume ratio of the bus and the amount/quality of insulation in the ceiling and walls, we can only maintain a 15 – 20 degree differential between inside and outside.  However, even a 10 degree differential makes a big difference.)

Linda made a wonderful dish for dinner with farro (an ancient Italian grain), garlic, onions, mushrooms, and asparagus.  The dish was fragrant, earthy, nutty, slightly creamy, and with just enough chew to have a great mouth feel.  She paired it with a simple green salad and we opened the bottle of Lawrence Elk black currant wine we bought at the Prairie Berry Winery in Hill, South Dakota.  Being from Michigan, we have ready access to wines based on fruits other than grapes, especially cherry and pear.  The black currant wine was unique and very much to our liking, and I wish we had bought more than one bottle.  (I guess we will have to go back.)

We were wrapping up dinner and preparing for our evening walk when Cheryl stopped by to let us know that there was a cowgirl barrel racing event going on over by the Morningside Park grandstand.  We walked over to the small horse arena and joined them to watch cowgirl barrel racing, junior calf lassoing, and age 7-10 girls and boys goat tying.  Finally, the real west.  I snapped a few pictures and sent one to our two children.

When we felt we had been sufficiently westernized (and seen enough baby goats tossed to the ground and tied up to last us a lifetime) we continued our walk and found Charles and Connie Martin’s MCI bus conversion, which they had moved from Windmill RV Park to one of the generator only (24 hr.) lots.  We stopped to chat for a while and got lots of good tips regarding travel directories and resources.  It turned into a longer visit than we intended, but it was nice to spend time with fellow FMCA GLCC members.  By the time we left their bus the sun had set and the temperature had dropped, so we had a chilly walk back to our coach.  The coach was still closed up with the ACs on, but the compressors had disengaged and it was a pleasant 78 degrees F inside.  We opened the rig up for the evening and had some fresh sweet cherries (Rainer’s) for a dessert snack.  It was then off to bed as we are scheduled for a tour of the local coal mine tomorrow at 9 AM.

 

2013_06_25 (Tue) Another Short Move

We knew we would be changing RV parks within the CAM-PLEX this morning, so right after breakfast I dealt with sewer, water, and electric hookups while Linda secured the inside for our short but potentially bumpy trip.  Bob Pinner came by around 8:00 AM to check on us, and came back around 8:30 AM to lead us to the appropriate area in Boxelder RV Park.  We had our choice of spots and picked one that was level and dry, indicating relatively good drainage, with a good stretch of road in front of it.  We chose site D-67 and pulled through into the site from the west so we would be parked facing east.  For the nine previous prior days we have been parked facing west such that the hot afternoon sun streams in our large expanse of windshield, making it difficult to keep the front of the coach cool.  It has been dropping into the 50’s at night, so the coach is cool by early morning and the morning sun on the windshield is welcome.

For some reason known only to Jasper (our 9 year old male mackerel tabby cat) our preparations to move the coach spooked him and he managed to get under the passenger-side built-in furniture (again).  We finally figured out that he was gaining access through a loose heat exchanger screen.  He also managed to get to a spot where we could not get to him to pull him out, so he stayed there while we moved to our new site and set up.  He decided to hunker down and sleep for a while, but we eventually coaxed him out of the spot to a place where we could get him out.  He had disappeared under this furniture once before.  Now that we knew his method of entry Linda secured the heat exchanger screens.  We think/hope we are finally done with this.

Before we were settled in to the new site, John & Cheryl pulled in next to us on the driver side in their Tiffin Allegro Bus.  They were also at Windmill RV Park yesterday and had also agreed to move to Boxelder RV Park today.  They were packed and ready to go when they saw us pull out, so they started up and followed us over.  Rick, our driver-side neighbor at Windmill, was almost ready to leave when we pulled out, and not long after John & Cheryl pulled in, Rick pulled his Foretravel U295 into the site on our passenger side.

As we were all getting set up in our sites and chatting, I was reminded of the degree to which RVers tend to be sociable and make friends quickly and easily.  This is not universally true, of course, but it is more often than not the case.  I suppose the obvious reason for this is the commonalities of the lifestyle, specifically the traveling experiences, destinations, and technology.  We also tend to be “people of a certain age”, retired with grown children and grandchildren.  Although we come from many walks of life, and are probably more different than we are similar, the moirés of the RV sub-culture emphasize and leverage the commonalities.

Based on the weather forecast we had originally planned to go to Devil’s Tower National Monument today.  Although we were set up in our new site by 10:15 AM, we decided to “stay home”, work on some small projects, and relax.  Our new 10 foot Camco water hose turned out to be defective, when the hose came loose from the barbed push-fitting (again).  Although I could probably fix it with a hose clamp, we decided to take it out of service and wait to see if the Camco vendor we bought it from at the FMCA rally would also be at Escapade and try to return or exchange it.  It’s a matter of principal.

After lunch we deployed the patio awning to shade the bus as the passenger side now faces due south.  I then went on an errand run to Home Depot, where I bought a hose clamp (just in case), a 10″ carbon filter element, a folding 2-step mini-stool (to make it easier to deploy/store the awnings), and some small plumbing parts I needed for a project in our shower.  I also found Eastside RV and purchased a 10′ fresh water hose so I could reconnect our water softener.  Cherie Ve Ard of Technomadia is big on the idea of serendipity, and I had a small dose of that today, although technically it was more of a “silver lining” experience.  Since the water softener has a sediment filter on the input side, I decided to replace the sediment filter in the coach’s incoming water line with a carbon element.

Our new water softener with pre-filter

Our new water softener with pre-filter

Imagine my surprise when I unscrewed the housing and discovered that there was no filter element inside!  If not for the failed Camco hose, I might not have discovered this for quite some time.

I purchased an Oxygenics shower spray a while back to install as a replacement for both our shower head and body spray, neither of which worked very well.  The Oxygenics is really a hand held sprayer that comes with a holder that threads on where the shower head normally goes, allowing it to serve a dual purpose.  It is also designed to draw in air and mix it with the water (thus the name) which is supposed to give a more invigorating shower experience while using less water.  I capped off the other connection where the original body spray hose was attached.  The installation appeared to be successful; the water only comes out where/when it is supposed to.

Late in the afternoon we drove to the local Wal-Mart to buy some new work clothes (jeans and T-shirts) and pick up some grocery items.  We had a simple but delicious dinner of lentil loaf and fresh steamed asparagus, and then went for a walk.  I played some more with the front OTA TV antenna and picked up several more channels.  I also decided that the position scheme I deciphered for the rear antenna was almost certainly not correct for, and therefore not applicable to, the correctly functioning front one.  I came to this conclusion based on the fact that we can see (with our eyes) seven TV towers from our site, so we know exactly which direction the antenna needs to point in order to pick up their signals.  I will eventually have to remove the front antenna top cover to physically verify how it works, but with warm, sunny weather forecast for the rest of this week, that task will wait for more agreeable conditions.

 

2013_06_24 (Mon) The Time Between The Rallies

Today was laundry day, so after breakfast we gathered up clothes and linens.  During the morning Peter & Sybil pulled out of the spot on our passenger side and shortly thereafter Ed & Rosemary pulled in (50A, full hookup).  Linda left to do laundry, post office, and grocery store errands while I stayed with the coach and cats.  Charles & Connie Martin, another couple from our FMCA GLCC chapter, pulled in across from us with their MCI 102C3 bus conversion.  They were apparently given a hard time about parking at Windmill RV Park and were told they had to be on the west side of the paved road, which is only 30A & water (no sewer hookup).  When we made arrangements with the CAM-PLEX to stay between the rallies they clearly told us we could move to Windmill anytime after 10 AM on Sunday and that 50A full-hookup sites where first come, first served.  They even gave us a parking sign to put on our dash.  It became apparent that there was some confusion as to who was supposed to park where.

I got on my computer (not literally, of course), went into the WiFi Ranger control panel, and reduced the power from “high” (the default) to “medium.”  According to the manual (available online), the connection can sometimes be improved by using less power.  I still had full/excellent signal strength in the bedroom, so I was not sure which radio this setting controls, or if it controls both, or if there are even two radios.  I will probably try low power to see how that works, and talk to the WiFi Ranger folks about it when next we meet.

I worked on finishing my draft blog post for the previous day, and then went to work on hooking up the rear OTA TV antenna/rotator and TV set.  My technological luck of the previous day ran out when the antenna failed its internal calibration process, and would not rotate.  I went ahead and set up the TV, another 22″ Westinghouse LD-2240 (LCD/LED flat panel monitor) requiring an ATSC channel scan activation code.  (Really, what’s up with that?)   I was able to find and view most of the same channels we had up font, but the reception was not as good on some, probably because the antenna was not pointed in the right/best direction.  A double check of the inside wiring confirmed that the RF & control cables were connected correctly, so the problem was either the roof unit wiring or the roof unit itself.

It was also possible that the problem was the rotator controller.  I tested that possibility using the known-good front unit, but the rear antenna still wouldn’t calibrate.  Soooo, back up on the roof to check the wiring to the antenna.  The connections are on the rear underside of the housing, which is mounted on top of two brackets that place the underside about 8″ above the lower rear roof tray and just above the main roof.  If you are short (I am) and flexible (not as much) there is just enough room to lie down, reach under, and use a short screwdriver.  All of the wires were connected to the correct terminals, but I loosened and re-tightened them anyway, including the coax.  I climbed down and retested the system, and this time it not only failed to calibrate, it displayed “Er” on the LCD.  That’s what I call “negative progress!”

The installation and operation instructions indicated that the problem could be: 1) that the black wire was not connected (it was, on both ends), or 2) that something was blocking the rotor.  In the later case that “something” would have to be inside the sealed antenna enclosure.  However, warnings elsewhere in the instructions tell you, emphatically and in no uncertain terms, that the insides of the system are dangerous (high voltage) and that it should not be opened as there are no user serviceable parts inside.  Huh?  So how do I unblock the rotor?

(BTW:  these are HD View 360 antennas from AntennaCrafters.  There was an older model of this antenna on the coach when we bought it.  It was designed primarily for the old VHF/analog TV signals and not optimized for the new UHF/digital ones.  The rotation feature also no longer worked, but we liked the sealed, “flying saucer” design in which the rotating antenna parts are in a flat, weather-sealed enclosure that is fairly aerodynamic going down the road.  I believe the antenna is an “active” design and provides some amplification of the signal it receives, but I am not absolutely sure of that.  The new model has a controller with an RF remote and is designed to pick up the newer digital signals as well as the legacy analog stations that are still operating in some areas.  Even though I was putting these two antennas in service for the first time, they were way out of warranty (90 days) as I had purchased them back in 2012 when we were having the roof redone and the coach repainted.  Based on my sample of two, it appears that AntennaCrafters has a 50% failure rate on this model.  I also have the problem that I bought these antennas from two different sources at two different times, and I don’t which one is which.)

At this point I will probably open up the rear antenna case.  After all, with electrical engineering degrees and amateur radio licenses, I figure I’m qualified to do this without endangering my life.  But with a storm approaching, that wasn’t going to happen right away.  We closed up the coach and turned on the two front air-conditioners to try to keep the interior comfortable as the forecast high was 91 degrees F.  The temperature outside was only 82 degrees F, but the sun was intense and the inside temperature was headed for 90.

We sat outside for awhile as it was cooler than inside, and watched a large thunderstorm develop northwest of Gillette.  It was drifting to the northeast, but also expanding in size.  As the southeast edge neared our location, and the winds picked up, we decided to put all of the awnings up and put the fold-up camp chairs away, not wanting to risk getting caught with them out should the storm change course and get cranked up.  We stood outside and talked to Ed and Rosemary while we watched the storm develop all around us.  It eventually started to sprinkle where we were so we went inside and soon had a heavy downpour that lasted for 15 -20 minutes.  The winds were not overly strong, and our skylight leak (slow drip) did not reappear.  The storm eventually moved on to the east.  Besides the drama and beauty, the upside of the storm was that it blocked the sun and brought cooler air, both of which helped keep the outside temperature down and the coach more comfortable.

I have loved western thunderstorms since I first encountered them as a boy traveling with my parents.  The combination of isolated development and unobstructed views to expansive horizons allows you to watch them develop for a long time as they move across a considerable distance.  This is rarely the case back in Michigan where storms develop along frontal boundaries and are often embedded and obscured from view.  Also, except in some flatter/cleared agricultural areas, views are not as expansive as in the west due to the extensive tree cover.

After dinner, and with the storm moved off to the east, I went back up on the roof to work on the rear antenna.  The enclosure is held together by 8 screws inserted from underneath, but it is high enough above the roof to allow for a 4″ long screwdriver to be used.  I had disassembled our old one when it was removed from the coach, so I had some idea of what to expect inside.  The physical design hasn’t changed much, but the rotor was definitely binding.  With nothing to lose, I moved it by hand and got it freed up, although I have no idea what, if anything, I may have broken in the process.  I had Linda apply power to the controller, being careful not to come in contact with any of the deadly voltages I had been warned about in the instructions.  It completed the calibration process this time and gave a direction number on the LCD.  Success!  (Maybe?)  I had her cycle it several times, and it calibrated successfully each time, but the rotor was not consistent as to its position.  I then had her slowly step through the 16 positions, up and down, several times.  Based on what I saw, it appeared that position 1 is just to the driver side of the front of the bus.  As the numbers increase the rotor turns counterclockwise, with position 16 just to the passenger side of the front of the bus.  So positions 1 -4 appear to be port side bow quadrant, 5 – 8 port side stern quadrant, 9 – 12 starboard side stern quadrant, and 13 – 16 starboard side bow quadrant.  This is, of course, with the double-headed arrow on the enclosure pointing towards the front (bow) of the coach.  Both antennas are mounted this way, but since I moved the rear rotor by hand, its position may not be correct.  It was also not as repeatable in its positioning as it should be, especially around positions 7 – 10, so the front one may not orient the same way.  Since the instructions are absolutely silent regarding how the pointing direction corresponds to the number on the controller display, I will ultimately have to take the front enclosure apart and visually determine how it works.  That would be easier, of course, if it wasn’t 8 inches above the roof and 13 feet off the ground at the time.

While I was on the roof, Bob Pinner stopped by.  Bob and Molly are the Escapade Directors for The Escapees RV Club.  He confirmed rumors we had heard earlier in the day relative to parking issues.  It turned out that the Escapade had lost the use of three RV parks at the CAM-PLEX due to the damage done by the motorhomes departing the FMCA rally.  The SKP’s had not planned on using Windmill RV Park, but now needed it for their staff and volunteers as well 30 A electric (only) registrants.  It was obvious that Bob was trying to re-plan a lot of things at the last minute so we agreed to move our coach the next day.  The decision was to move us back to the Boxelder RV Park, where we would have full hookups, and a good chance of 50 A power.  We figured the sooner we moved the better site selection we would have, so we agreed to move first thing the next morning (8 AMish).

In spite of the issue with the rear TV antenna, we were able to use the rear TV and simultaneously watched different TV programs for the first time in quite a while as we do not currently have OTA, cable, or satellite TV at home and we do not have satellite TV in the coach.  Gillette has PBS and Create, so this was the first time it felt a little bit more like living in the coach and a little bit less like being on vacation.  The fact that we are between rallies with no pressing need to be anyplace specific, or do anything in particular, also contributed to this feeling.

2013_06_23 (Sun) FMCA Comes To A Close

As usual, the exodus from the FMCA 50th Anniversary rally started early, with some motorhomes pulling out as early as 6:00 AM.  It is always an interesting experience to watch the departure process from a major RV rally.  Unlike the arrival process, which is highly organized and managed by the organization running the rally, the departure process is completely asynchronous and self-managed.  It is not, however, chaotic; to the contrary, it is quite orderly.  People leave when they need to and are ready to go, and that just seems to work out well.  They are attentive and considerate, and there’s never any congestion; just a random but steady flow of RVs.

We had considerable rain the past few days, and some of the parking areas developed minor flooding and very muddy soil.  Inevitably, some motorhomes were stuck and had to be pulled out.  We have been in that situation on two previous occasions, but our site this past week was high with good drainage and well-graveled roads.  Except for a few soft spots, notably where people cut corners too tight at intersections, there were no serious problems in Boxelder RV Park.

We had already arranged with the CAM-PLEX office to move to the Windmill RV Park this morning, so after breakfast we drove the car over to scout out a level, 50A full-hookup site.  We left the car there to “hold” a spot, which were first-come, first-served, and walked back to the coach.  We did our usual departure thing of unhooking the utilities, putting up the awnings, and otherwise preparing for the short, slow move.  We had no problems pulling out, and took paved roads over to our new site.  Once we were parked we did our arrival thing and leveled, hooked up, and settled in for the next few days.

We are staying at the CAM-PLEX while we wait for our early entry date on the 27th for The Escapees RV Club Escapade rally, which will also be at the CAM-PLEX June 30 – July 5.  We will extend our stay here until July 7 and then move to Sheridan, Wyoming for two weeks to work on a Habitat For Humanity build.  It appears that we will have to move again on the 27th to a different RV Park here at the CAM-PLEX as the Escapade is not using this one.  But for now we have 50A power, which will allow us to run our air-conditioners.  With some hot days forecast, that’s a good thing.

We decided to deploy our new Zip Dee Awnings, both to shade the coach and to let them dry out.  Much to or surprise, we discovered that we could fully deploy the large patio awning following the directions we had.  (We left our directions at home.  The ones we had came from the Zip Dee booth and did not match our hardware exactly.)  With the upper rafter arms hooked onto the roller tube shaft we could not get the latch pins on the rafter arms to engage.  Our analysis of the problem was that that the fabric was either 2″ too short or the upper rafter support arms were 2″ too long.  I wrote an e-mail to Zip Dee, but fortunately it never got sent.  Further study of the rafter arm revealed that the hook on the free end was attached to a spring-loaded inner tube that was free to slide inside the outer tube.  The available travel was just enough that the hook could be placed over the roller tube shaft AND the latch pin could be engaged.

Perhaps it is part of still being new to extended-time RVing, but the awning episode was yet another example of the emotional roller-coaster that sometimes comes with this lifestyle.  First comes the surprise and then the disappointment of discovering (yet another) problem.  This is followed by the frustration and annoyance of not being able to figure out what’s wrong and/or fix it.  Then a certain sense of helplessness arises at not being able to get assistance or parts (things always seem to break on Sunday, so it’s rarely a “day of rest”).  Next is the dread brought on by considering the possible dire consequences of continuing the journey with the problem unresolved.  A sense of resignation settles over you as you accept that the problem will remain unfixed for the time being and will probably require a change of plans and added expense somewhere down the road.  Then the “ah-ha” that comes from food, release from anxiety, and time for further thought.  And finally, the satisfaction and sense of accomplishment that comes from having figured it out and fixed it, even if only temporarily.

Along the same line, we were discussing our broken searchlight over lunch and decided that it would be better to seal it up with Rescue Tape and not use it than try to repair it.  The wires inside the base go through a hole in the roof that is not sealed.  Removing the base opens up the possibility of water getting in through that hole if I am not able to get it resealed.  As we rarely need/use the searchlight, that was too big a risk for too little benefit.

As we were finishing up our encampment routine, we had motorhomes pull in on either side of us; Peter & Sybil on the passenger side and Rick on the driver side.  Peter & Sybil had purchased a Progressive Industries portable 50A EMS from Lawrence RV Accessories during the FMCA rally.  It had been working fine, even through the big storm, but quit working when they moved to Windmill RV Park and hooked up.  I looked at the unit and noticed moisture in the LCD display (where it should not be).

I shook the unit and thought heard a sloshing sound, indicating that water had probably gotten in to the unit and shorted something out.  I checked the outlet with my multi-meter to make sure the power supply was properly wired and providing the correct voltages so they could at least plug in and have power.  Sybil called Daryl Lawrence and he answered the phone even though it was Sunday!  They were still at the CAM-PLEX and came right over.  Daryl examined the unit, came to the same conclusion I had, and swapped it out for a new one.  The PI EMS units are generally very reliable, and the company stands behind them and the vendors who sell them.  Peter & Sybil were leaving the next day for North Dakota, so this was truly great service for a great product from a great RV vendor.  (We got our Progressive Industries EMS-50 from Daryl a year or so ago and rely on it to protect our coach’s electrical systems from problems arising outside the coach.)

As long as I am on the subject of PI EMS units, when we changed campsites and plugged in I followed the maintenance recommendation I received a few days earlier from the owner regarding the buzzing coming from the unit.  Immediately after applying power, during the 2′ 16″ time delay before power switches through, I quickly cycled the contactor by moving the override switch back and forth.  Sure enough, the buzz disappeared.  (Technical note:  Although the unit is sealed, it is designed to have the cover removed so wiring connections can be made.  Dust can and will build up on the contactor contacts which results in a degraded electrical connection and the resultant buzzing.  The contacts arc slightly when they close and open, and cycling them quickly and repeatedly cleans them.)

Fixing the "ET" searchlight

Fixing the “ET” searchlight in Windmill RV Park

In the afternoon we got the Little Giant ladder out and configured it as a 14′ extension ladder.  I climbed up and attached the searchlight head to the base using some of the rescue tape we bought from a vendor at FMCA.  The light can still be turned on and tilted up/down, but cannot be turned side-to-side.  This is a temporary fix until we can get the bus inside at Phoenix Paint and do a proper repair with Michele Henry’s help.  This will probably be in conjunction with the GLAMARAMA rally in Goshen, IN September 18 -22.  What is unknown at this point is how well it will hold up to travel at highway speeds.  That test comes in a couple of weeks.

While I was on the roof I inspected the skylights and vent fan domes for damage from the recent hail storm, but they all appeared to be fine.  I then made a temporary installation of the WiFi Ranger Mobile Titanium (WFR-MT) by zip-tying it to the weatherhead cable entrance on the front roof.  I fed the cable through the weatherhead while Linda pulled it into the former ceiling mounted TV cabinet directly below.  (This cabinet originally housed a 19″ CRT TV.  That TV was removed and a door made by Jaral Beatty of Logansport, Indiana to cover the opening.  The door is walnut veneered plywood with solid walnut edging and Jaral managed to match the existing wood finish very well.  Because this was a former TV cabinet, AC power was already available inside.

With power to the WFR-MT, we were able to connect to the local/secure network and reconfigure it.  We were then able to select one of the public/open WiFi signals that were still available at the CAM-PLEX and connect through to the Internet.  The signals were very strong and the connection steady and reasonably fast.

After dinner we went for a walk and watched another beautiful sunset.  As dusk turned to night we witnessed the rising of a “super moon”, which appeared 14% larger than normal due to a slightly closer lunar orbit.  (The 14% is something Linda read online, we did not measure it.)

When we got back to the coach, Linda decided to watch Inspector Lewis on her iPad via our free WiFi connection.  We were able to stream the entire episode without hesitations due to frame-buffering.  That’s a pretty good WiFi connection!  A lot of RVs had left the CAM-PLEX by this time, so competition for the bandwidth was obviously less than during the FMCA rally, but it was still impressive.

Since we appeared to be on a technological roll, I decided to (finally) hookup the front over-the-air (OTA) TV Antenna, rotor controller, and TV set (monitor).  What’s this about going online to get an Access Code to enable ATSC scanning on the TV set???  Yup, our Westinghouse 22″ LCD/LED TVs require an activation code that can be obtained online, by text message, or by phone.  Fortunately, we had all three methods available to us so we got the code, entered it into the set, and away it went.  Ta-da; we have PBS and Create!  Now it feels like home.  🙂