Tag Archives: 40-foot tower (house)

2015/11/03 (T) The Penultimate Cut

I heard noises in the kitchen at 7 AM and thought the cats might be up to something.  I got up and discovered that Linda was just leaving the house.  She is normally out the door between 6:15 and 6:30 AM but did not set her iPad alarm last night.  I stuck my head out the door and said “good morning” as she was getting in the car.

I had my usual breakfast of granola with fresh blueberries and brewed a half pot of Sumatra Mandheling half-caffe coffee.  I was enjoying my cup-a-joe by the fireplace when Linda called to let me know there was a story coming up on Michigan Radio (WUOM) at 8:30 AM about an underground landfill fire in Bridgeton, Missouri.  Bridgeton is where my sister, niece, future nephew, and grand-niece live and I had just heard about this fire for the first time on Sunday evening while talking with my sister.

I got the leaf blower out at 10 AM and spent a couple of hours blowing as many leaves out from under bushes and away from the house into the yard as I could.  Keith arrived at 10:30 AM and followed his usual mowing pattern starting with the west half of the property.  The lawn in the immediate vicinity of the house is the last area he cuts which gave me enough time to get the leaves out into the yard where Keith could mulch them.

Most of our trees have dropped most of their leaves by now and Keith’s mower did a pretty good job of mulching most of them.  Before he left we discussed having him come back one more time.  The grass has quit growing so my preference is to wait two weeks but that will depend on the weather.  Keith will check with us next Monday and we will decide what to do at that time.

Mike (W8XH) is planning to come over tomorrow after breakfast and help me work on the tower and our Hi-Q 6-80 antenna.  I have been collecting materials that I need and took a little time to see if they would work with the tower.  I also took the Diamond X-300N antenna down as I planned to put it on the tower in place of the X-50N that is currently up there.  My materials were not working quite the way I had hoped they would so I headed to Lowe’s to see what else I could find.  I also planned to drop off the used oil and filters from the bus at O’Reilly’s Auto Parts store.

At Lowe’s I found clamp sets designed for mounting antenna masts and bought a pair.  O’Reilly’s parking lot was still closed off.  It looked like it had been re-blacktopped and they were painting the stripes for the parking spaces.  This was my second attempt to get rid of the waste from yesterday’s bus maintenance.  I will try again tomorrow; with any luck the third time will be the charm.damage

The area beneath the co-pilot/navigator seat.  Not a pretty sight, especially when racing against the clock to get the coach finished for the upcoming winter season.

The area beneath the co-pilot/navigator seat. Not a pretty sight, especially when racing against the clock to get the coach finished for the upcoming winter season.

I finally got back to work on the bus at 2:30 PM and removed the front passenger chair pedestal base.  The entire area under the base, between the side-to-side seat mounting channels, was rotten so I cut out the water-damaged wood.  Just below the wood I found rusted metal which appeared to be delaminating.  Metal does not do that so I presume there was a layer of sheet metal on top of a metal housing.  The main structure of the bus is welded stainless steel but mild steel was obviously used to create compartments.  Ugh.

After cutting out the damaged wood the remaining piece towards the outside was loose but would not come out.  I removed a couple of screws from the 1/4″ walnut veneer side panel and pried the top out with a small screwdriver.  This panel has a lot of switches mounted in it and a lot of wires behind it so I could only pull it out about four inches.  That was enough to see a 3/4″x3/4″ piece of blocking screwed to the floor to catch/secure the bottom edge of the panel.  It also enough to see a very large nest made of tiny bits of shredded paper.

The cavity behind the panel to the right of the co-pilot/navigator seat was apparently a great place for a mouse to build a nest.

The cavity behind the panel to the right of the co-pilot/navigator seat was apparently a great place for a mouse to build a nest.

I left the nest alone for the moment and removed two screws from the block that went into the piece of wood I need to remove.  It appeared that a drain line for the front air-conditioner went through the floor near the outside edge and possibly some wires.  I left the nest for Linda to see and will resume working on this tomorrow.

Linda made vegan grilled cheese sandwiches for dinner and served them with some of the leftover broccoli soup and sliced fruit.  We each had a small glass of the Frey Natural Red organic/vegan wine.

After dinner I called Phil to see what his plans were for this week vis-a-vis our driveway and French drain projects.  I got his voice mail and left him a message.  When we left on Saturday afternoon he was just finishing up placing and compacting the gravel in the driveway but said the west end of the yard needed to dry out (again) before he could finish working down there.  Hopefully the new drain will help speed that process along.

The floor area under the driver’s seat in the bus with all of the rotten wood cut out.

The floor area under the driver’s seat in the bus with all of the rotten wood cut out.

Phil uses a self-leveling laser level system to measure elevations.  Not only has he assured me that the new 40 foot parking area is level, he has demonstrated it with his system.  Still, it does not look level, especially from certain points of view, and it does not feel level when driving in it, although that may also be an optical illusion.  We have a transit level and I plan to use it to check the pad, but it requires two people, one to hold the measuring stick and one to look through the telescope and record the readings.  That means I need Linda’s assistance, which means this will have to wait until the weekend.  Perhaps by then I will have the cockpit in the bus repaired.  It’s also possible that Phil will have returned and completed the job, I which case I may have him help me use the transit as a check on his laser system.

We watched our usual lineup of Tuesday evening TV shows while Linda checked in on her online word games and I worked on this post.

 

2015/06/30 (T) Three Score and Five

Today was a milestone birthday for Linda.  We had our usual leisurely early morning with coffee, fresh fruit, and cinnamon raisin toast (from Metropolitan Baking) for breakfast.  We talked some more about our long-term ham radio plans and decided we would order one (1) of the new Yaesu FTM-400DR/DE dual band mobile radios and a slightly more powerful VHF/UHF base station antenna.  Our daughter called around 9 AM to wish her many happy returns of the day.  My Michigan Public School Employee Retirement System (MPSERS) health insurance shifted her to secondary, with Medicare as primary on June 1st, the first day of the month in which she turned 65.

The temperature was in the low 60’s when we got up at 6:30 AM.  The weather forecast for the afternoon had an increasing chance of rain and the possibility of isolated thunderstorms so Linda went for a mid-morning walk.  I headed to my office to order the radio and a Diamond X-300NA 2m/70cm antenna.  All of the online distributors are selling the radio for the same price.  I decided to buy both products plus the RTSystems programming software, from Amateur Electronic Supply (AES).  Their UPS Ground shipping is “free” and since they are based in Ohio the shipment will be here in 1-2 days rather than 4-5 days.

I took a break and spread three more bags of brick pieces around the base of the tower and in front of the cable entry box.  Back in my office I dealt with some personal e-mail.  I sent an e-mail to Scott (KE9FOX) at QTH.com with additional information he needed to transfer the SLAARC website and domain name registration from GoDaddy to QTH.com.  I then gathered up a load of laundry and put it in the washer.

By the time that was all done it was getting close to lunch time.  Lunch was a big spinach and lettuce salad, baby carrots, a few sourdough pretzel nibblers with roasted red pepper hummus, fresh sweet cherries, and the blueberries/strawberries/raspberries that were left from breakfast.

After lunch I transferred the laundry to the clothes dryer and then got cleaned up.  We left around 3 PM for the U.S. Bar and Grill in Wayne and stopped on the way to get a card.  Today was John Smallwood’s last day at Wayne RESA and there was a gathering from 3-to-6 PM to see him off.  John was the VP of the Wayne County Salaried Staff Federation (WCSSF) and succeeded me as President of the local when I retired.  Now it was John’s turn to enjoy a well-earned and well-deserved retirement.  This was the second gathering for a colleague in the span of just over a month.  Besides wishing John well it was an opportunity to reconnect with other former colleagues.

After a suitable amount of time visiting at John’s party Linda and I drove to the Mongolian Barbecue in Novi for a celebratory birthday dinner.  It is a very noisy restaurant but was not as bad on a Tuesday evening as it was the last time we were here on a Saturday.  I would have preferred a quieter and more relaxing atmosphere, but the Mongolian Barbecues have a lot of ingredients that we can eat and we find the method of preparation very much to our liking.  By the time we had a small bowl of soup, a moderate sized salad, and a good size bowl of ingredients we were full.

I had a brief QSO with Chris (K8VJ) on the drive home.  I stopped at the Shell station and topped off the gas tank in my car so we would be ready to go in the morning.  We finally got home at 8:30 PM.  Linda made some hot tea and we each had a piece of Prickly Pear Cactus Jellied Candy.  I restarted the dryer on Touch Up and checked my e-mail.  We were tucked in by 10 PM as we needed to be on the road by 7:30 AM tomorrow.

 

2015/06/24 (W) Up The Tower

Today was the day to finally climb the tower to remove an old TV antenna, reposition an amateur radio antenna, and install two new antennas, one for OTA TV and the other for a cellular booster system.  But there were other things to do before I was ready to climb.

I was up at 7 AM and on my way to Lowe’s in Howell by 7:20 AM in search of a solution to the problem of how to mount the outdoor cellular booster antenna.  I ended up buying two 2-1/2 inch U-bolts.  Although the tower legs are 1-5/8″ in diameter the angle bracket attached to the bottom of the antenna is 2-1/4 inches wide.  Thus I needed the 2-1/2 inch spacing for the threaded ends of the U-bolt to clear the bracket.

Back at the house Linda was up and had the coffee made.  We had a quick breakfast of homemade granola.  I removed the tire pressure sensors and GPS from my car and headed to Brighton Honda to drop it off for its 100,000 mile service appointment.  Linda arrived at the dealership about 10 minutes later.  We then headed to Adams Electronics in Wixom.  While Adams Electronics primarily serves the public and business communications markets owner Scott Adams, AC8IL, is a long-time ham and a member of the South Lyon Area Amateur Radio Club and Novi Amateur Radio Club.  Well known in the local amateur radio community, Scotty is the local go-to guy for certain kinds of equipment.  I ordered two coaxial cables from him the other day and we were here to pick them up.

We left to return home at 10 AM so I called Mike (W8XH) to let him know we were running a little behind.  So was he, but thought he could be at our house by 11 AM.  That gave me time to drill a hole in each of the two U-bolt retaining plates and cut a short piece of 1″ square aluminum tube to use as a spacer.  That was the last fabricating I needed to do and we got busy staging all of the materials we were going to need to get the tower work done efficiently.

Setting up the tools and parts outside the "drop zone" of the 40-foot tower on the east end of the house.

Mike (W8XH) setting up the tools and parts outside the “drop zone” of the 40-foot tower on the east end of the house.  (Photo by Linda)

Linda set out a sheet near the tower but not in the “drop zone.”  We spread out materials and tools on the sheet and used it to make sure we could find things quickly and keep them from getting lost in the grass.  I also brought all of my tool boxes to the tower area.  With everything assembled it was time to climb.  I set up our 7 foot step ladder on the east end of our rear deck to provide access to the roof near the tower.  Mike helped me into his climbing harness and got it adjusted.  Once on the roof I took the harness off temporarily as my first task was to remove the 2m/70cm base station antenna.  After clipping the plastic cable ties I lowered it down to Mike while Linda took photographs.  (She helped with many aspects of the work today but was the only photographer.)

Starting up the tower from the roof of the house.  (Photo by Linda)

Starting up the tower from the roof of the house. (Photo by Linda)

I put the harness back on and Mike tossed me one of the 100 foot ropes which would eventually be used to haul materials and tools up and down the tower.  I secured the haul rope to one of the unused seat clip rings and Mike instructed me on how to secure the harness while climbing.  I put the waist strap around the tower and clipped it in.  I then put one of the two fall cables, attached to the ring at my upper back, around one of the legs above one of the cross bars above my head and clipped it into the ring at my chest.  The tower is adjacent to the east end of the house and is attached to it by two pipe assemblies just below the soffit (the house has hip roofs) so it was easy to step onto it.  After that things got tougher.

The horizontal trussing on the tower is two feet apart vertically.  That spacing was right at the limit of how high I could lift my right foot and required me to pull myself up part way until I could push with my right leg.  Once up on the next rung I attached the other fall cable, moved the first one higher, and slide the waist strap up to position myself for the next step.  I repeated this pattern with the two fall cables and the waist strap as I worked my way slowly up the tower, clipping old plastic cable (zip) ties as I went.  The tower definitely had some give but I was quickly acclimated to the amount of sway and found it to be acceptable so we decided not to guy the tower with the other three ropes, which would have slowed my ascent even more.

When I finally reached the top of the tower I untied the haul rope, looped it over one of the southeast facing horizontal bars and hauled it up allowing the free end to lower down to the ground.  Mike then tied the rope to the standoff pulley I had fabricated and hauled it up to me.  I already had cable ties, a diagonal cutter, and a pair of slip pliers with me.  I set the threaded rod on the northeast and southeast cross bars, inside and against the two legs that were parallel to the side of the house, and secured it with cable ties.  This was a three-handed job that I had to do with two hands but I got it done while only dropping one cable tie.  With the pulley rod secured I undid the rope and then undid the knot tying the two loose ends together.  I fed one end through the pulley and retied it to the other end.  We now had a way to haul materials and tools (in a bucket) up to me at any needed height while keeping it 18 inches away from the tower.

Three-quarters of the way up ad working with the haul rope.  (Photo by Linda)

Three-quarters of the way up ad working with the haul rope. (Photo by Linda)

The next task at the top of the tower was to remove the old TV antenna, mast, and rotor.  When I finally had a close up view of these old components it became apparent that my best course of action was to try and unclamp the base of the mast from the rotator, lift it off of the rotator, and toss it to the ground.

The mast clamp parts were all very rusty so Linda got the WD-40 and Mike sent it up in the bucket.  I sprayed the nuts on the mast mounts and also the rotator leg clamps.  I tried undoing the mast clamps with a slip pliers but it was no good, so Mike sent up three open/closed end wrenches.  One of them was the right size and to my surprise the rusted nuts broke loose and started backing off.  One of them did not want to come off but unscrewed the entire bolt instead.  Fine.  The bolt had a screwdriver slot in the top and was threaded into the rotor housing and I did not care how it came out as long as it did.  I got the mast clamps loose enough that I could work the bottom of the mast free from the top of the rotor.  There was a lot of rust there too.  After clipping some coax cables, rotor control wires, and plastic cable clamps I repositioned myself up one rung on the tower so I could get enough leverage to the lift the mast clear of the rotator collar and control it well enough to make sure the antenna fell to the ENE away from the house and my helpers down below.  And that is exactly what happened.

The first antenna to get mounted was the outdoor antenna for the cellular booster system.  Mike sent the antenna up in the bucket along with the various pieces I needed to secure it to the short top/center mast support tube so the entire antenna, which is omnidirectional, was above all parts of the tower.  What would have been an awkward assembly on the ground took on added difficulty 40 feet in the air but I got it secured with good access to the N-female connector on the bottom.

At the top with the pulley in place and using it to haul up a bucket with tools and parts.  Mike is controlling the haul rope on the ground.  (Photo by Linda)

At the top with the pulley in place and using it to haul up a bucket with tools and parts. Mike is controlling the haul rope on the ground. (Photo by Linda)

We decided to run the coax on the outside of one of the tower legs rather than down the inside of the tower.  Mike tied the LMR-400 coax to the rope and hauled it up to me.  In addition to the haul rope Mike tied a second control line to the bucket to keep it from swinging all over the place.  I connected the coax to the antenna feed point and then wrapped the connection with coax seal tape.  I then routed the coax down the east leg of the tower and zip tied it to take the weight off of the antenna connection.

Next up was the 2m/70cm amateur radio base station antenna, often referred to as a 2m/440 dual band antenna.  (In this nomenclature the “2m” refers to a range of wavelengths for one of the VHF ham bands and the “440” refers to a range of frequencies for one of the UHF ham radio bands, so it is a mixed units designation.). The antenna is about five feet long with three short counterpoise (ground plane) rods near the base.  It had an LMR-400 style cable connected to it but with PL-259 male connectors on each end.  The antenna feed point is an N-female connector so I had an adapter installed to make everything compatible.  Mike removed the coax and the adapter, zip tied the antenna to the haul cable at three points, put the 10mm wrench in the bucket, and hauled it up to me.

The ham radio antenna was also tricky to get mounted.  I installed it at the top of the northwest leg so that most of the antenna was above the tower and two of the three short counterpoise were parallel to the west (N-S) and northeast (NW-SE) crossbars.  The antenna by itself is light in weight but it is five feet long and mounts at the bottom nine inches, so most if it was above me with a tendency to wave around in mid-air.  With the coax connected, however, it weighed quite a bit more.  I temporarily zip tied the coax to take the weight.  I then had to hold the antenna with its base against the northwest post at my head level, push a U-bolt through the mounting bracket and past the tower leg, slip the mating clamp over the two ends of the U-bolt, and then get a small lock washer and nut on each threaded bolt end.  I then had to repeat this for the second U-bolt.  Again, a three-handed job that I had to do with only two hands.

The old OTA TV antenna and mast on the ground.  It came down by the gravity method.  (Photo by Linda)

The old OTA TV antenna and mast on the ground. It came down by the gravity method. (Photo by Linda)

The bonus to this work at the top of the tower was a commanding view of the surrounding countryside, which was mostly trees in every direction.  I even saw two towers far to the north and was kept company by a soaring vulture just to the NNE.  I was also able to determine that the tops of the large white pine trees behind the east end of our house are about 10 feet higher than the top of our tower, putting their overall height at about 55 feet as their bases are lower than the base of the tower.  We plan to put the 70 foot tower at a spot that is surrounded by these trees on three sides (W, S, and E) so the top of the tower, and any antennas mounted there, will be well above the tree tops.  That is especially important as we plan to eventually put an HF beam antenna up there on a mast attached to a rotator and it will need to be able to rotate freely for 360 degrees.

The final antenna was the hardest.  The Antennas Direct DB8e OTA UHF/digital TV antenna was very large and heavy by comparison to the other two.  In this case ‘heavy’ meant a few pounds.  It is actually two UHF antennas mounted at the end of a dual support arm structure.  The support arm mounts to a vertical pole, such as a tower leg, at its midpoint and there is a combiner box located there as part of the mount.  A short length of RG-59 (75 ohm) coax connects each antenna to the combiner box and the main coax connects there as well.

How tall the tower appears (and feels) depends on where you are standing.  (Photo by Linda)

How tall the tower appears (and feels) depends on where you are standing.  Pulley and haul rope in the upper right.  Lots of coaxial cables to be dressed (secured) on the way down.  (Photo by Linda)

RG-59 is a different kind of coaxial cable from the LMR-400 used for the first two antennas.  LMR-400 has a 50 ohm characteristic impedance and is used for receiving and transmitting RF energy with considerable power if needed.  RG-59 is much smaller in diameter, more flexible, has a 75 ohm characteristic impedance, and uses F-connectors that are the standard for OTA TV, video, and satellite cables.  But I have gotten ahead of myself.  I had to come down a few feet on the tower to install the TV antenna but before doing that I had to start securing the transmission lines to the tower legs with cable ties.

Mike rigged up the haul rope in a ‘Y’ to lift the antenna from its center of gravity while actually attaching the rope to its ends.  That allowed the haul rope to both support the weight of the antenna and keep it oriented correctly while I positioned and clamped it to the southwest tower leg with the dual support arms pointing in an east-west direction.  Because of where I had the pulley mounted, and the length of the ‘Y’ in the support rope, I had to mount the antenna a few feet lower on the tower.  Fortunately the slightly lower height was not going to affect its performance.

Like the ham radio antenna, the OTA TV antenna mounted to the tower leg at two points.  The upper assembly was a U-bolt with a retaining bracket on the back side.  The lower assembly was a pair of straight bolts that went through the combiner box past the tower leg and had a retaining bracket on the back side.  The antenna came with wing nuts instead of washers and regular nuts, which helped a little, but I really needed three hands to get the antenna into position and tighten the mounting brackets.

Mike ties off the DB8e OTA TV antenna with an inverted "Y" so it will haul up in the proper orientation.  (Photo by Linda)

Mike ties off the DB8e OTA TV antenna with an inverted “Y” so it will haul up in the proper orientation. (Photo by Linda)

Once I had the antenna sufficiently attached to the tower I was able to position the support arm close to the southeast facing side of the tower.  I then pointed the antenna on the east end of the arm ESE towards the Detroit area TV towers and tightened the two nuts on the mounting studs.  (The horizontal dual support arms are about 3 feet long so I was able to reach through the tower to get to the mounting studs and nuts.) I left the antenna on the west end of the support beam loose and turned it out of my way so I could complete other tasks.

Mike attached the end of the main RG-59 coax to the haul rope, put the amplifier and a 2-foot length of RG-59 coax in the bucket along with lots of zip ties, and pulled them up to me.  The amplifier is about 3″ wide by 2″ high and 1.5″ thick including the concave plastic backplate.  The backplate accepts two zip ties for mounting to a pole.  I positioned the amplifier about 8 inches below the antenna combiner box and cinched up the two zip ties.  I then connected the short coax to the combiner box output and put the combiner back it its protective, weather-gasketed plastic box.  I connected the other end of the short coax to the amplifier input and wrapped the connection with coax seal weatherproofing tape.

Installing the DB8e OTA TV antenna required three hands.  Note that I am installing it at the highest point possible when suspended from the pulley with the haul rope in an inverted "Y" attachment.  (Photo by Linda)

Installing the DB8e OTA TV antenna required three hands. Note that I am installing it at the highest point possible when it is suspended from the pulley with the haul rope in an inverted “Y” attachment. The yellow waist strap allowed me to lean back and work while the two red security straps would catch me if something broke. (Photo by Linda)

I attached the main RG-59 coax to the output of the amplifier, which is also the DC power input, and wrapped the connection in coax weather seal tape.  I then dressed the cable and secured it to the tower leg.  I aimed the antenna on the west end of the support arm WNW towards the East Lansing TV towers and tightened the nuts to lock it in position.

At this point I was finally done working on the antennas but had three coaxial transmission line running down the outside of the tower, one by each leg.  As I descended the tower, reversing the protocol I used going up, I secured all three cables every few feet.  I finally had my feet back on the roof at 2:20 PM, almost exactly 2 hours and 30 minutes from when I started climbing.  Projects usually take me twice as long as I think they will but this was about half as long as I thought it would take, so we were all pleased that the work had gone smoothly and relatively quickly.  My main objective was to get the old TV antenna down and the three antennas up but my secondary objective was to only climb and descend the tower once.  Mission accomplished, at least for now.

By now we were all hungry and thirsty so Linda made chickpea salad sandwiches and set out fresh sweet peppers, sliced apples, baby carrots, and cold water.  After a suitable lunch break we returned to the next phase of the work which was routing the coax cables into the cable entry box (CEB) and making the connections.

We started with the RG-59 coax from the OTA TV antenna.  I coiled the extra cable and hung it on the tower (with zip ties, of course), routed it into the CEB and connected it to the power inserter / lightning arrestor.  We purchased this cable from a Radio Shack store in Florida two winters ago to hook up our bus to the RV resort cable TV system.  Besides the coax it had a separate ground wire.  The amplifier and the power inserter both had connections for a separate ground wire so I connected it on both ends.

Routing coaxial cable into the cable entry box from the tower and the basement and making the connections.  (Photo by Linda)

Routing coaxial cable into the cable entry box from the tower and the basement and making the connections. (Photo by Linda)

We had already routed a 75 ohm video cable from our bedroom TV to the sump pump room in the basement.  I selected a suitable length of this same type of cable from our existing inventory, connected it to the other side of the power inserter, and routed it through the back of the CEB into the sump pump room where Linda guided it.  Conveniently, I had a double-ended F-female barrel connector designed to connect together two cables with F-male connectors.  I plugged in the AC power adapter for the power inserter, which was already in the sump pump room, and we went upstairs to see if we were receiving any TV stations.

We set the ‘Source’ on the TV to ‘Antenna’ and did an ‘Auto Scan’ for digital channels only.  There are very few analog TV signals still in use and the ones that are reside in the old VHF TV spectrum which our new antenna cannot even receive.  The scan found 58 signals, which obviously included the sub-channels.  Besides the main Detroit stations and the East Lansing PBS station we got other Lansing area stations and even a station from Flint.  The nice thing about digital TV is that if you get a picture at all it is very good.

There is a large TV tower at I-96 and US-127 on the southeast corner of Lansing so we were probably picking it up.  There are several TV towers SSW of Lansing about 35 miles that serve Battle Creek and may serve Lansing and Kalamazoo.  They are 50+ miles from us and I did not have the west antenna pointed in exactly that direction but it may have been close enough to pick them up.  Flint is at least 35 miles away straight north off the sides of both antennas so theoretically we should not have received any stations from that direction.  We will have to check the AntennaPoint.com website and confirm by station identifier what stations we are actually receiving.

Feeling good about our success so far we routed the coax for the cellular booster across one of the support arms that brace the tower to the house just under the east soffit.  We dropped it down next to the wall and brought it into the bottom of the CEB, replacing the hole plug with a rubber grommet.  Routing it this way kept it out of the way of future foot traffic, or lawn and garden work, in the space around/between the tower and the CEB.  I connected the cable to the lightning arrestor and coaxed it unto position inside the CEB.  LMR-400 is stiff and bending it sharply will damage it.

I connected one end of the 15-foot LMR-400 cable to the other side of the antenna arrestor and routed it into the sump pump room where Linda guided it into position.  I secured it to the ceiling, brought it down the opposite wall, put a large 180 degree bend in it, and attached it to the connector on the bottom of the cellular booster.  I turned it on and watched the lights blink for a while.  All three of us then started checking signal strength throughout both floors of the house.  All five of the ‘Alert’ lights went from blinking yellow, which means the unit is adjusting the gain on that band, to solid yellow, which is not described in the manual.  Since we had not yet registered the device with Verizon Wireless I turned off the booster.

Back out at the CEB I removed one of the hole plugs directly below the input of the Morgan VHF lightning arrestor.  We routed the coax for the 2m/440 ham antenna across the tower brace, down the wall, and around through the bottom of the box where I attached it to the lightning arrestor input.  I had an old piece of 50 ohm coax with an N-male connector on one end and a PL-259 (male) connector on the other end.  I attached the N-connector to the output of the VHF lightning arrestor and fed the other end through one of the 2″ conduits into the sump pump room where Linda routed it out into the ham shack.

We set our “Go Box” on the desk, plugged the PL-259 into the SO-239 socket on the back of the case, plugged it in to AC power, turned on the power supply, and turned on the radio.  The radio, an Icom IC-7000, came up tuned to the South Lyon (K8VJ) repeater.  I transmitted and successfully triggered the repeater, which is currently at a secondary site about 20 miles from our tower.  Mike went out to his car and used his mobile radio to verify that we could transmit to and receive from the repeater.  I had a lot of background static (white noise) so Mike switched modes and transmitted directly to our antenna.  The signal was full scale and full quieting.  I have a ground lug in the Go Box but did not have it connected.  I vaguely recalled that I had to ground the box at the previous house to eliminate a noise issue.  (The radio and power supply are grounded to the box.)

I switched the radio to UHF and it was set for the Novi repeater.  I listened but did not hear anyone transmitting so I transmitted, giving my call sign and a brief message, and then listened.  I did not get a reply even though Mike was also monitoring the Novi repeater so I switched back to the South Lyon repeater.  Mike indicated that I had, indeed, triggered the repeater and that a couple of other hams acknowledged hearing me in addition to him.  It thus appeared that I did not have something set up correctly on the receive side of the radio for the Novi repeater but the system (radio, cables, arrestor, antenna) was clearly working.

That was enough work for one day so we gathered up all of the tools and unused materials and put them away.  We offered to take Mike to dinner as a ‘Thank You’ for his assistance.  It was more than helpful to have someone on the ground who was familiar with tower operations.  We considered several dining options but opted for Olga’s in Brighton.  Linda and I had small salads, sans the Feta cheese, veggie Olga’s that were excellent, and curly fries without Tabasco sauce for the ketchup.  Warning:  As inconceivable as it may sound, Olga’s does not have any kind of hot sauce in its restaurants.  Mike had a dish with chicken in that he said was very good.

Mike headed home from the restaurant as did we.  We were tired but very pleased with what we had accomplished in the course of the day.  We celebrated our accomplishments by watching several programs on Detroit PBS, something we have not been able to do for more than two years.

 

2015/06/23 (T) Grounded

As I wrote in yesterday’s post we did not turn off the lights last night until almost 1 AM because we were keeping a close eye on the weather moving across the lower portion of Michigan’s Lower Peninsula.  Although strong to severe storms were still forecast from 1 AM to 5 AM they either did materialize at our exact location or we slept through them.  We had the house closed up and the air-conditioning on, so that cut down the sound level of outside noises.

A cold front had pushed through by sun up and we woke to a cool morning with blue skies and noticeably lower humidity.  We did not have any trees, or even big limbs, come down and there was no damage to our brand new roof.  The forecast yesterday was threatening enough, however, that in the morning we took the potted plants, and as much of our outside lawn furniture as we could find room for, inside including our sun umbrella and trash cans.  I planned to be gone most of the day, and Linda was leaving mid-afternoon to go to dinner and a movie with Diane Rauch, so our first chore was to put all the lawn furniture, plants, and other outdoor stuff back outdoors.

This week is mostly being devoted to ham radio with the ARRL Field Day as the crowning event this weekend.  My specific focus for most of the week, however, has been the “communications tower” adjacent to the east wall of our house.  As described in previous posts we installed a cable entry box (CEB), mounted the cellular booster in the basement, mounted the inside cellular antenna, and ran coax cables.  The antennas will (hopefully) be mounted on the existing 40 foot tower tomorrow, cabled into the CEB, and cables run from there to devices inside the house.  With any luck by the end of the day tomorrow we will have decent cellular service inside the whole house, the ability to watch OTA TV programs on two different TV sets, and finally be able to connect one of our radios in the ham shack to an antenna.  Today, however, was planned to mostly address other things.

I had an appointment with our dentist at 10:20 this morning and left at 9 AM.  I planned to stop at Chuck’s bus garage and check that the key he lent me worked, but I needed gas for my car.  I did not have time for both and did not really have a choice; I would have to check the key some other time.  I ordered two cables yesterday from Scott (AC8IL) at Adams Electronics.  Later in the evening I was unsure if I had specified the connectors correctly so I called and left a message.  I called again this morning to make sure the message got through.  It did, and my original connector specifications were correct.

I arrived at the dentist’s office about 10 minutes before my appointment time.  I called Rick Short at Isringhausen USA to make sure he was going to be in before I drove two hours to Galesburg, Michigan after my dentist appointment.  I got his voice mail a left a message.  “ISRI” makes very high tech air suspension driver’s seats that are used as original equipment in motorcoaches, semi-tractors, heavy equipment, and locomotives.  I would really like one for our bus, but it is not proving easy to get.

Dr. Steve and his assistant, Leslie, made molds of my upper and lower teeth and a bite impression.  The molds will be used to make a mouth guard that I can wear while I sleep.  Dr. Steve has a strong suspicion that I am clenching my teeth and the mouth guard will reduce or eliminate the irritation it causes.  I will have to ask if I can wear it during the day too as I am occasionally aware of clenching my teeth while I awake.

I had not heard back from Rick by the end of my appointment so I called the main number at ISRI and talked to the receptionist.  It turned out that Rick was not in today and she transferred me to Jeff Woodworth.  Jeff was willing to meet with me but thought it would be a better use of my time to wait until Rick was available.  My next opportunity to drive to Galesburg will be Thursday and I will likely go as the ISRI seat is holding up our ordering of Flexsteel seats through Coach Supply Direct.

I stopped for coffee and then re-routed for Chuck’s bus garage in Novi.  The key to the garage worked perfectly.  I called Linda to let her know about the change in plans and headed for home.  There is too much to do at the moment to waste much time so I installed the #4 AWG bare copper ground wire I bought yesterday at Lowe’s.  I mounted an offset copper wire lug using the center support stud for the copper back plane in the CEB.  I replaced one of the plastic hole plugs with a rubber plug with a small hole in the center.  The hole I chose in the bottom of the CEB allowed the ground wire to come straight up into the lug.

Another view of the cable entry box on the east end of the house by the 40-foot tower.

Another view of the cable entry box on the east end of the house by the 40-foot tower showing the bare copper ground wire that runs to the ground rod and then to one of the tower legs.

Outside the CEB I routed the ground wire around to the existing ground rod and secured it using the new clamp I bought yesterday.  There was an old ground wire connected from a clamp on the tower to the ground rod.  I removed that wire along with some coax and control wires that I had clipped when we removed the old satellite dish.  I then attached the new ground wire to the clamp on the tower.  While we were at it Linda trimmed back a small bush that was growing between the tower legs and I pulled leaves, grass and other stuff out from around the Day Lilies that we transplanted last year around the tower base.

With the CEB grounded we looked at how we might get a video cable up to the TV/monitor in our bedroom.  The wall where the TV is mounted has a hot water baseboard radiator that comes almost to the trim on the door wall.  That end of the radiator has a copper pipe that goes through the floor into the basement and it was easy to locate the pipe in the basement.  I determined that there was enough space behind the pipe to safely drill a hole but I had to drill it from the top side at an angle.  A 5/8″ wood boring drill bit created a hole just big enough for the molded F-connector on the end of the cable to pass through.

We fed the video coax cable above the suspended ceiling in the ham shack area to the location of the hole.  I then fed the cable up from the basement as Linda pulled it up into the bedroom.  We adjusted the amount of cable in the bedroom to allow the wall mounted TV set to move through its entire range of motion.  The other end of the cable was then routed into the sump pump room.

By the time we finished pulling this cable it was 3:30 PM and time for Linda to leave to pick up Diane.  They were headed to Royal Oak for dinner and a movie as the movie they wanted to see was only showing at the Royal Oak Main Theater.

While I was out during the morning Lynch Carpet had called to let us know our Armstrong vinyl tile was available for pickup so after Linda left I closed up the house and went to get it.  The 12 boxes of tiles, container of vinyl adhesive, and container of vinyl grout were all neatly arranged on a small pallet and tightly wrapped in shipping plastic.  Rather than break this down and load each thing individually they used a fork lift to set the pallet in the back of my Honda Element.  The rear suspension settled at least two inches when they transferred the full weight of the pallet to the floor of my car.

When I got back to the house I backed the car up to the garage.  I cut the shipping plastic loose and unloaded the tubs and boxes of tiles.  I put the pallet on the garage floor and then neatly stacked the boxes of tiles on it to keep them off the floor.  Each box contained 14 tiles measuring 16″ by 16″ for a total area of 24.89 square feet.  The Armstrong Alterna tiles are a “luxury vinyl” product, and are about 1/8″ thick.  Even so, the boxes were heavier than I expected so I decided to weigh one.  It tipped the scale at just under 42 pounds.  That meant the entire pallet weighed close to 500 pounds, and, ignoring the weight of the cardboard box, that is about 3 pounds per tile.

When I drew out the design I determined that I would need 158 tiles, some of which would be partial.  Figuring conservatively at 150 full tiles equivalent, and ignoring the weight of the underlayment, adhesive, and grout, the floor tiles will weigh about 450 pounds.  I have no idea what the carpet and ceramic tile that I have removed weighed but the tiles were heavy.  I also have no idea what the furniture weighed that we have removed but also have no idea what the new furniture will weigh.  The intent was that the new floor and furniture would weigh less than old stuff but we will see.

I traded phone calls with my dad and we finally got to talk for a half hour starting at 4:30 PM.  He turned 90 this past Sunday.  Mike Fearer from Bid-Rite Concrete called at 6 PM and arrived about 10 minutes later to discuss the foundation for our 70 foot ham radio tower.  I had printed off a page from the Universal Tower website showing their tower base.  I also downloaded and printed their base and tower installation instructions.  I had a set of these to give to Mike so he would have some idea of what the project is about.  We looked at the proposed location for the tower and access for his dump cart.  We also talked about the base, a rebar cage, a form around the top of the hole to allow the concrete to be slightly above ground, and a jig to make sure the base is level and the tower is plumb.

He said he was interested in the job and would work with me and Phil Jarrell (the excavator) to get it done.  Rather than bid the job he would just do it for time and materials.  He also said the current price of concrete was about $100 per cubic yard.  We will need about six (6) cubic yards to fill the required 5′ x 5′ x 6′ (deep) hole.  He thought he might be available the middle of next week but I don’t think I could have everything pulled together that quickly.

After Mike left I went to Lowe’s and picked up five 40 pound bags of topsoil, a 1-in/2-out signal splitter (rated for 5 MHz to 2.4 GHz), and a plastic snap cover channel for hiding the video cable we ran up into the bedroom from the basement for the TV set.  I then went to the Meijer’s supermarket just across Grand River Avenue for soy creamer but they did not have what I was looking for.  As long as I was there I had a salad for dinner at the in-store Subway.

While I was sitting there I called Mike Sharpe (W8XH) to confirm that he was available tomorrow to help with the antenna installations on our 40 foot tower.  I mentioned that the only thing I lacked was a standoff with a pulley at the end of it for hoisting stuff up to me.  He suggested that something like that was essential and I agreed, so I headed back to Lowe’s to see what I could figure out.  What I ended up with was a three foot long 7/16-14 threaded rod, a pulley that had a closed eyelet on top (and was big enough for the 3/8ths rope I bought), some 7/16ths washers, and some 7/16-14 nuts.

When I got back to the house I unloaded the topsoil near the part of the east yard that needs to be filled in, took the other stuff inside, and then assembled the threaded rod pulley system.  I secured the pulley on one end of the rod using two of the nuts, one on either side of the eyelet.  I threaded a nut onto the other end, put on two washers, two nuts, two more washers, and another nut.  I ran the first two nuts, with two washers between them, part way down the rod.  I left the second pair of nuts, with washers between them, near the end of the rod.

I took the assembly out to the tower and adjusted the position and spacing of the two pairs of nuts and washers so they would bracket two of the horizontal tower members.  In use I will secure the rod to the tower at each pair of nuts/washers using plastic cable ties.  This arrangement will put the pulley at least 18″ from the tower which should be far enough out that we can hoist the DB8e OTA TV antenna to the top of the tower without it banging into the tower or hanging up on something.  This antenna is the largest thing we need to hoist up. The old TV antenna is considerably larger and heavier, but it is coming down via gravity.

There was a message on our answering machine from Linda’s sister, Sr. Marilyn, who lives in St. Louis.  She was listening to the news earlier today about the storms that went through our part of Michigan and wanted to make sure we were all OK.  By the time we finished talking it was dark and I was done working for the day.  Linda called shortly thereafter to let me know she was on her way home and I mentioned the call with Marilyn.

I finally opened the box with the vertical omnidirectional outside antenna for the cellular booster system and discovered that I should have opened it sooner.  The mounting bracket was designed to be mounted to a vertical surface, such as the side of a house, not a tube, such as a tower leg.  I did not want to postpone tomorrow’s tower work so I will have to get up early and figure out a way to adapt the existing bracket so I can mount the antenna to the top of the tower.

My initial thought was that an aluminum U-channel of the correct size might solve the problem very nicely.  I could drill two holes in the bottom of the “U” to match the two holes in the bracket.  I could then drill three pairs of holes through the sides of the channel.  The antenna would be bolted to the bottom of the channel.  With the open part of the channel held against a vertical tube I could secure it with three long plastic cable (zip) ties.  Conceptually it should work and be easy to fabricate, but will take time which I won’t have a lot of in the morning.  We have to get the two coax cables from Scotty (AC8IL), drop off my car at Brighton Honda for its 100,000 mile service, and be back in time to have the mount fabricated and all of the antennas and tools ready to go by 10:30 AM when Mike shows up.

Linda got home at 9:45 PM, earlier than she thought she would when she left.  She and Diane ate at Luigi’s and had a very nice meal.  They also enjoyed the movie.  We had a big day on tap for tomorrow and we asleep by 10:30 PM.

 

2015/06/14 (N) WordPressing

We had yet more rain overnight.  I heard the rain around 6 AM and checked the Wundermap app on my iPad but did not get up.  Linda did not need to go to the Howell Farmers Market today as the refrigerator is quite full and the rainy weather made the prospect less appealing.  We finally got up at 9 AM and I made coffee.  Linda checked the weather forecast.  It called for a 100% chance of rain between noon and 3 PM with thunderstorms and up to 2″ of rain.  By 10:15 AM it was raining steadily again.

We deferred by one more day getting back to work on the bus.  The monthly meeting of our South Lyon Area Amateur Radio Club (SLAARC) was this evening and we did not want to get involved in physical work today.  I wanted to do a load of laundry but deferred that as the high humidity makes it harder to get the clothes dry.

I opened the three boxes that made up the OTA TV antenna shipment from AntennasDirect.com and laid all the parts out on the floor.  As I wrote yesterday I need to determine exactly what types/lengths/connectors I need to get everything hooked up and make sure I have it on hand before I climb the 40 foot tower next to the house.  After I laid all of the parts out this morning Linda asked how I was going to get all of that stuff up the tower.

Our new Antennas Direct DB8e Over-The-Air TV antenna.

Our new Antennas Direct DB8e Over-The-Air TV antenna.

My plan is to preassemble as much stuff as possible.  I will then take a 100 foot rope with me when I climb the tower, loop it over one of the crossbars, and drop it back down to the ground where Linda can tie it to a bracket, or directly to some part, and pull it up to me.  As I describe this it occurs to me that I should probably rig up a pulley.  We also figured out that we should run the TV co-ax inside the house before I climb the tower.  That will allow Linda to scan for signals and talk to me on our portable ham radios while I am on the tower if the antennas need to be aimed.  I called Mike (W8XH) to see if he would bring his climbing harness to our ham radio club meeting this evening and he agreed.

For breakfast I had some of the Pepperidge Farm cinnamon chocolate chip bread Linda bought and we both had fresh grapefruit.  After breakfast I got cleaned up and dressed and then partially assembled the OTA TV antenna.  I then went to my office and settled in at my desk to upload blog posts.  I had not been in my e-mail for a few days so there were some things I had to respond to before working on our blog.

I got my blog posts uploaded for May 29 through June 7 and then decided to update the other three WordPress websites I work on.  Much to my dismay I was not able to log in to the FMCA Freethinkers website.  I got an error message instead and the contents looked to me like the site might have been hacked.  I notified the President of the chapter and indicated that I would contact the ISP technical support folks and see what they can tell me.  I have never opened that site up to the members of the chapter because I never quite finished it but I intended to and I have a lot of time and effort invested in its development.  Still, if the site is totally corrupted I may just delete it and abandon the whole project.

I wrapped up my work just in time for dinner.  Linda reheated the two leftover vegan cheeseburgers and served them with the remaining vegan potato salad and fresh nectarines.

Linda spent a little time during the afternoon getting the treasurer’s report ready for our SLAARC meeting.  We left at 6 PM and were at the Witch’s Hat Depot in South Lyon by 6:30 PM.  We have changed the meeting format to have social time from 6:30 to 7:00 PM, followed by a business meeting, and then a program.  I got the climbing harness from Mike (W8XH) as soon as we arrived and put it in the car.  I then had a brief chat with Scotty (AC8IL) regarding Universal Towers in Clinton Township, Michigan and LMR-400 co-ax.  Scotty stocks LMR-400 but also stocks RG-213 which he thinks is better for outdoor use.  His opinion is based on a Motorola white paper that discusses potential problems with the aluminum foil wrapped copper braid outer conductor in LMR-400 in the presence of moisture.

Tonight’s business meeting was a discussion about preparations for the upcoming ARRL Field Day lead by this year’s club field day chair Paul (KD8SNZ).  The program was a presentation by Larry (K8UT) on the N1MM Logger+ contest logging program that we will be using to log contacts on four different networked computers.  Larry is a member of the N1MM development team.  I asked Larry if I could send him the URL for my broken WordPress website and he said he would look at it.  We left at 8:45 PM.

When we got home Juniper was hunched over something in the living room and I could see immediately that she had caught another mouse.  It was very small, like the last one, and for all I know it was the same mouse.  I got her to drop the last one and it escaped into my office.  Linda grabbed one of the antenna boxes and pulled out the shipping paper that was stuffed inside.  I managed to get Juniper to drop the mouse in the box, from which it was not going to be able to escape, and then took the box outside and set it free.  If it has any sense it won’t come back in the house and it will tell all if its little mouse friends to steer clear of this place.  Juniper is a very skilled hunter and will catch anything in that house that moves that is smaller than she is.

Linda prepared some fresh strawberries and served them with some non-dairy ice cream.  She logged in to Amazon.com and ordered six live traps and a new cover for my iPad, both eligible for Amazon Prime.  We then spent a little more time reading and writing and checking the weather.  The 10-day forecast is for continued rain almost every day.  We are still expecting the new roof shingles to be delivered tomorrow but we won’t be surprised if they are not.  We are also expecting that Apex will have to push the start date of our project back due to all of the recent rain delaying other jobs that are ahead of ours.  We turned in for the night at 10:30 PM; late for Linda and early for me.  She was asleep fairly quickly but I stayed up writing and played a few games on my iPad as I do most nights.

 

2015/06/13 (S) On to Illinois

It has turned out to be a wet June so far and we had more heavy rain last night.  In spite of waking up during the night I was up at 7:30 AM and made coffee.  Everyone else got up as suited their level of rest and we sat around chatting for a while.  Ron put a load of laundry in the washing machine and then we sat down to a light breakfast.

Ron and Mary spent most of the rest of the morning repacking all of their stuff for the drive to northwest Illinois and their week-long bicycle ride.  FedEx Home Delivery delivered the Cyclo 5-Pro Mark II Dual Head Orbital Polisher I ordered along with all of the foam pads and detailing chemicals.

Ron retrieved their laundry from the dryer and after they finished packing we had a light lunch.  By 1 PM they were ready to load up the car so we helped get their bags out.  After a brief “farewell and safe travels” they were on their way.  They had a five hour drive but would gain an hour as they entered the Central Time Zone so they would be at their motel by 5 PM local time with plenty of daylight and time to eat dinner.

Linda took a short nap and then went for a walk.  I read through the manual for our SureCall Fusion5s cell phone booster and was part way through the manual for the Cyclo 5 when I decided to take a nap.  Linda returned from her walk and a little while later a USPS mail carrier delivered the OTA TV antenna I ordered from Antennas Direct.  All I am waiting for now is the cable entrance box I ordered from KF7P Metalwerks.

Once the cable entrance box arrives I will have a bit of a project.  First I will need to drill two 2″ holes through the east wall of the house and into the sump pump closet in the northeast corner of the basement, mount the box to the wall, and ground it to the outside ground rod by the tower.  I may also need to install additional ground rods.  I will then need to climb the tower by the house and do the following:

  1. take down the old OTA TV antenna and rotator;
  2. mount the new OTA TV antenna and aim it;
  3. mount the amplifier for the OTA TV antenna;
  4. attach a short piece of 75 Ohm co-ax from the antenna output to the amplifier input and weatherproof the connections;
  5. attach a longer piece of 75 Ohm co-ax to the output of the amplifier and weatherproof the connection;
  6. mount the outside antenna for the cell phone booster system;
  7. attach one end of a 50′ piece of LMR-400 or RG-213 co-ax to the cell phone antenna and weatherproof it;
  8. unmount our Diamond SG7900 2m/70cm ham radio base station antenna and remount it at the top of the tower;
  9. attach a 50-to-60 foot length of LMR-400 or RG-213 co-ax to the ham radio antenna;
  10. dress and secure all of the coaxial cables with plastic cable ties (zip ties).

Once I am done with tower work I will need to do the following to complete the installation:

  1. install the lightning arrestors in the cable entrance box for the cell phone booster and OTA TV (?) co-ax cables;
  2. route each of the co-ax cables into the bottom of the cable entrance box and attach them to appropriate lighting arrestors;
  3. attach additional co-ax cables to the lightning arrestors and feed them through the 2″ holes into the basement;
  4. mount the Surecall Fusion5s in the sump pump room and connect the co-ax for the outside antenna and the power supply;
  5. run a 50′ length of LMR-400 from the sump pump room across the basement ceiling and up through an old vertical furnace exhaust chase to the attic;
  6. drill a hole in the ceiling of the main floor hallway near the chase;
  7. mount the inside done antenna for the cell phone booster system to the ceiling with the co-ax dongle in the attic;
  8. connect the antenna dongle to the co-ax coming up from the basement;
  9. run additional co-ax from the sump pump room to the ham shack;
  10. run additional co-ax from the sump pump room to the video distribution point in the laundry room (or directly to the locations of the two TV sets);
  11. turn on the Fusion5s booster (transceiver), adjust the gain (if needed) and test it with our phones and Mi-Fi;
  12. test the TV sets (and hopefully not have to go back up the tower to reposition the antenna);
  13. connect our Icom IC-7000 amateur radio and test the antenna connection.

As I wrote out this list it occurred to me that I need to make a list of all of the co-ax types/lengths/connectors I need and that, at a minimum, I probably need to order a length of LMR-400 orRG-213 co-ax cable and the proper N-connectors to complete the ham radio antenna connections.  It also occurred to me that I might be able to do some of the inside wiring while I am waiting for the cable entrance box to arrive.  Also, once the TVs are connected Linda can scan for channels and communicate with me with our HT ham radios if I need to change the aim of the antennas on the tower.

All of this reminded me that I need to follow-up with a Bratcher Electric on running a new 100 Amp main feed from the transfer switch to the panel in the furnace room in the garage.  I also need to order some new split foam fillers from Critter-Guard and new electrical hardware for connecting the bus to the toad from EZ-Connector in California.

I must have been sleeping lightly and dreamed all of these details because I got up from my nap around 5:30 PM, finished reading the manual for the Cyclo 5, and then took a shower and got dressed for dinner.  Barb Spera had called Linda yesterday to see if we were available for dinner this evening.  They had really enjoyed our meal at La Marsa in Brighton a couple of weeks ago and wanted to go again so we agreed to meet them there at 7 PM.  We did not have to wait for a table and our waiter, Najheem (Naa-gheem), was delightful.  Barbara had the Koshary again, and Chuck had the Chicken Shwarma with tabbouleh salad, while we split an order of spicy vegetarian ghallabah with rice and a salad.  I had a mango smoothie and we all enjoyed the swarm pocket bread and garlic spread.

It was after 9 PM when we got home and we headed off to bed at 10.  We knew Ron and Mary had arrived at their destination because Ron played a Scrabble word.  Linda had also checked that our daughter and son-in-law were on their way back from Las Vegas.