Tag Archives: Flexsteel Barrel Chair

2015/06/01 (M) Bradd and Hall et al

The temperature dropped into the upper 40’s last night.  Although the temperature in the bus only dropped to about 64 degrees F I was cold and did not sleep soundly.  The electric heater pad is still on the mattress but was not plugged in so I could not use it.  Linda developed a bad sore throat during the night (there are no good ones) and also did not sleep well.  We got up around 7 AM and I made coffee while she got dressed and drove to the nearby Martin’s supermarket for Ibuprofen and Chloraseptic throat lozenges.  Sore throats are no fun.  We both hope this passes without requiring medical intervention.

We are in the newest section of Elkhart Campground which consists of narrow pull-through 50 Amp full hookup sites that are long enough to leave a towed car connected to a 45 foot motorhome.  The section is not full but the motorhome on our passenger side had their GLAMARAMA 2015 parking and volunteer placards in the window this morning.  We finally opened our registration packet and found that we also have a volunteer placard since Linda is volunteering at the registration table.  We also discovered that we could have arrived at the Fairgrounds this morning and stayed for no charge.  Oh well, Elkhart Campground is more convenient to Bradd and Hall and other Elkhart area vendors and if we checked into the rally we would immediately be working and socializing instead of shopping.  One must be clear about their priorities.

Bradd and Hall is open from 9 AM to 5 PM Monday through Friday.  We got there around 9:45 AM and had just gone inside when I got a call from Curtis Coleman.  We was headed east on I-80 from Iowa with his sights set on Cleveland and Columbus Ohio and did not realize we were in Elkhart.  He brought me up-to-date on some things having to do with RVillage and we discussed him coming to our house to hang out once he had taken care of some business later this week and we got back home from the rally.

At Bradd and Hall we were assisted by Stephanie.  Bradd and Hall had a good selection of Flexsteel Captain’s chairs and Lambright Comfort Chairs but did not have any Flexsteel barrel chairs.  That was more than disappointing as we thought the Flexsteel bolt down barrel chair might be just what we need to provide seating, with seat belts, on the passenger side of the coach that can swivel to face anywhere from forward to aft.  They had two Flexsteel Captain’s chairs that we found comfortable enough and were not too large.  Either one might do nicely to replace the front passenger seat, and possibly to replace the driver’s seat, although I am holding out for an ISRI air-suspension driver’s seat.  We took cell phone photos of each of us sitting in various seats, photographed product tags, and got several fabric samples but were no closer to a decision about seating when we left than we were when we arrived.

On the drive back to the campground we stopped at Factory RV Surplus to look for some electrical components but ended up looking at furniture.  They had a barrel chair that we liked but no identifying information on it.  We did, however, get some free popcorn.  We were headed up SR-19 and decided to go on up into Michigan and pay Michelle Henry a visit at Phoenix Paint.  There did not appear to be anyone around so we left and went back to our coach and had a bite of lunch.  We had planned to also visit Lambright Comfort Chairs in Shipshewana, but we had been there before and figured they would not have anything different from what Bradd and Hall had on display.  With both of us being tired and Linda still not feeling well we decided to stick around the bus and continue to do online research.

Sometime during the afternoon I got a call from Jim Marin wanting to know where we were parked.  From our windshield I could see their motorcoach parked up by the office waiting to come into the campground.  The space to our passenger side was vacant so they registered for that one and pulled on around and in.  Jim and Lydia have a 1997 MCI 102DLS-3 Vantare conversion that they bought last September.  It’s a nice coach and they got a good deal on the purchase.  They got plugged in and set up while we connected our car for towing and then we stood around visiting in the cool temperatures and warm sun.

We were showing them what we have done to the inside of our coach and explaining what we plan to do when there was a knock on the door.  It was Curtis Coleman.  He had decided that Elkhart was far enough for one day and knew we were here as a result of our conversation this morning so he pulled in for the night and was parked one spot up from Jim and Lydia.  We made introductions, finished looking at our coach and then toured Jim and Lydia’s bus.  I brought my tape measure and tried to quantify the size of their furniture which appeared to fit very nicely in the available space.  All of us then went to Curtis’s coach, which is also a 1997 Vantare conversion of a Prevost XL, and got a sense for his seating.  Both coaches have ISRI driver’s seats and both Jim and Curtis really like them.

We had eaten dinner earlier so Marin’s returned to their coach for their evening meal and we left Curtis to tend to Augie Doggie and take care of RVillage business.  Curtis came over later to visit and we sat in our coach in three lawn chairs and had a great chat.  He returned to his coach at 10:45 PM and we went to bed a short time later.  It was forecast to drop into the mid 40’s overnight so I closed the roof vents and turned on the electric heater pad on my side of the bed.

 

2015/05/25 (M) Memorial Day

We spent the morning lounging around drinking coffee and enjoying the holiday.  Hey, even retired people need a day off.  Actually, we continued to research refrigerator, seating, and upholstery options for the bus, taking a break to have a tofu scramble and toast for breakfast.

We stumbled upon the Yale Appliance blog which proved to be very informative.  Yale is a very large appliance store in the Boston area and maintains a blog about appliances.  After reading what they had to say in some fairly recent postings we realized that we should probably not be looking for a “counter depth” refrigerator.  It also appeared that our best bet in terms of case dimensions and interior volume might be a standard top freezer design and our best bet in terms of both price and reliability might be a Frigidaire.

We went to the Frigidaire website and found that the FFHT1621QB might fit our needs perfectly.  It is a 16.3 cu. ft. top freezer design available in black, white, or stainless steel with doors that can be hinged left or right.  (We need a fridge with doors the hinge on the left.)  It is 28″ W x 30-1/8″ D x 64-3/8″ H and only needs 3/8″ clearance on the top and sides and 1″ in the rear.  The depth includes the doors and handles; the depth of the case alone is only is 26-5/8″.  Our refrigerator alcove is 33-3/4″ W x 29-1/2″ D x 66-3/4″ H so it will fit easily, recessing a bit more than our current 22.6 cu. ft. Jenn-Air and leaving 5″ to its left for a pull out pantry.  The pantry will have be custom built and measure approximately 5″ W x 28″ D x 66″ H including top and bottom mounted slides/guides.  Also of importance, we will not have to modify the cabinet above the refrigerator alcove.

In terms of seating we checked out Gilbreath Upholstery’s website but then concentrated on the Bradd & Hall website.  Bradd & Hall is a well-known RV (& marine) furniture supplier in Elkhart, Indiana.  They handle the Flexsteel RV and marine product lines and also sell the Lambright Comfort Chair product line, although the latter is available directly from Lambright in Shipshewana, Indiana.  We have sat in the Lambright Lazy Relaxor Lite swivel recliner (wall hugger) at RV rallies and found it nicely sized and very comfortable for us.  It is 24″ W x 33″ D x 38″ H and needs 2.4″ clearance from the wall.  It is normally a free-standing chair so we are unclear whether it can be secured to the floor or be used with seat belts.  We plan to visit Bradd & Hall on Monday, June 1 before we check into the GLAMARAMA rally and this is one of the things we will ask about.

Bradd & Hall also sells a Flexsteel Barrel Chair with a bolt down pedestal base that locks in different positions and includes a bar for attaching seat belts.  It is 26″ W x 30″ D x 34″ high and might be a better fit for our bus and what we are trying to accomplish with our remodeling project.  Last, but not least, they sell Flexsteel Captain’s Chairs (which Flexsteel calls “bucket seats” on its website).  We need a chair of this type to replace the oversized front passenger chair and possibly to replace the driver’s chair.  My hope, however, is to get an ISRI 6800 seat for the driver’s position.  These are the seats that are normally installed on tour buses.

An advantage to getting everything from Bradd & Hall, except for the ISRI driver’s seat, is that we can get the same fabric on the passenger Captain’s chair and living room chairs and buy additional materials to have the seat and back cushions made for the sofa that I will build (with storage underneath).  We will probably find a folding chair for the desk and can have the seat recovered in the same material so that everything is coordinated.

Linda called the J. C. Penney’s salon to see if Renee was working and had openings.  She was, and she did, so Linda booked a time, grabbed her car keys, and headed to Twelve Oaks Mall.  That seemed like an opportune time for me to head to the bus to double check measurements and ponder design solutions.  I checked the dimensions of our refrigerator alcove and the Frigidaire FFHT1621QB will definitely fit very nicely.  The front part of the passenger side of the bus has 13′ 3″ of flat floor space available for a desk and two chairs with a small dining table between them.  On the driver side of the bus the aft end of the sofa nook is 7′ 2″ from the entrance step.  If I can fit both chairs and the table in the first 7′ 2″ on the passenger side we will have room for a 6′ long desk that is 26-1/2″ deep.  That’s long enough to have a file drawer on one end and a printer shelf on the other end with plenty of room in between for a chair.

We have been planning on reusing the Corian top from the old dinette table so I decided to disassemble the top from its base.  I had never really looked at the construction before now and discovered that the Corian is glued to a wood panel that is secured to the two massive posts that are screwed to the base.  I was able to disconnect the base from the posts easily enough but there did not appear to be any way to separate the Corian from the support structure.  I took a few whacks at it with a pry bar and small sledge hammer and it was clearly not going to come loose.

The good news is that we can now select a new table top in whatever size, shape, and material suits us and use the same material for the desk top, which will double as additional kitchen counter space.  Our assumption has been that we will use Corian, but Corian is heavy so we will consider other options before making a final decision.  We discussed extending the desk top all the way down the wall to the front of the living room, although it would only be about 6″ deep at most, and building shallow cabinetry to go under it and fill in the space above the HVAC chase and below the window trim.  That space will essentially be wasted otherwise, and have to be finished in some way, so building small storage spaces is worth considering with or without the extended desk top.

What all of this comes down to is that we have to select the two chairs we want to use in conjunction with figuring out the table size and support system, and then finalize the design of the desk.  We plan to recondition all of the woodwork (with Touch of Oranges and Touch of Beeswax) and replace the refrigerator before we install the new floor, which has to go in before the furniture.  That’s the order in which decisions have to be made and the work has to be done.  Chairs and custom woodwork are potentially long lead items so we need to get them finalized and ordered, but they are the last things to get installed, so it should work out OK in the end.

It rained hard for a brief time mid-afternoon, after which Linda went for a long walk.  She was walking almost daily this winter in Quartzsite, Arizona but has not walked much since we got home.  That gave me time to work on this blog post.

Earlier in the day we snacked on nuts instead of having lunch.  Linda made whole wheat capellini for dinner using the Portobello mushrooms and some of the asparagus we bought yesterday at the Howell Farmers Market.  It was delicious.

I had intended to work at my computer most of the day but that obviously did not happen.  When I finally went to my office after dinner I had a long chat on the phone with Butch about hardware for the slide out pantry and other bus-related things and then checked a few websites that he suggested as good sources of specialized hardware.  I then e-mailed GLCC members about parking with the chapter and took care of some other e-mail.  In addition to computer-based work I need to keep working on the bus but I am also at the point where I need to order some things and then settle in and work on drawings for the desk, pantry, and sofa.