Tag Archives: US-27 (FL)

2016/04/06-10 (W-N) Close Call All’s Well

2016/04/06 (W) Near Disaster

We were up by 7 AM, anticipating our departure from Jetty Park and the Cape Canaveral / Cocoa Beach area of Florida.  Around 9:30 AM we started straightening up the interior of our motorcoach.  At 10:15 I moved the car over by the office and walked back to our site.  Around 10:30 I disconnected the shorepower cord and stored it for travel.  With the chassis batteries connected, and the engine compartment accessory air supply open, the engine started right up.  After the chassis aired up I raised the tag axle and Linda served as spotter while I eased out of site #357.  I thought I might need to back up to get clear of vehicles and trees but I was able to exit the site in one smooth forward motion.  Linda got onboard and we drove clockwise around Red Knot Circle and over to the dump station by the office.  There is a large paved area around the dump station with room to temporarily park the bus, without blocking any of the vehicles parked there, while we connected the car for towing.  We checked the lights, which were OK, and Linda got onboard.  We pulled out of the campground just after 11 AM and once I cleared the turn out of the campground exit I lowered the tag axle.  I felt a sudden jerk but thought the transmission had shifted.

We headed west on George J. King Blvd. and merged onto FL-A1A westbound.  FL-A1A quickly crossed the Banana River, leaving Cape Canaveral for Merritt Island.  We eventually crossed the Indian River and were back on the mainland.  Somewhere along the way FL-A1A became FL-528 which eventually became FL-528 Toll Road.  Linda was keeping tabs on the temperatures and pressures of all the wheels/tires.  The driver side tag seemed to be running consistent with the others and we settled in for our trip.

FL-528 traverses a large swath of undeveloped land with lots of water and birds.  Traffic was light and the driving was easy so it came as quite a jolt when we got a high temperature alarm on the driver side tag axle tire sensor.  The temperature was in the 160’s and climbing and I started looking for a safe place to pull off the road.  Before I could do that I checked the driver side rear view mirror, and saw smoke coming from the tag axle wheel well.  NOT GOOD!  I pulled off at an entrance ramp to get farther away from the traffic lanes.  I told Linda to get our cats into their carriers and grab our computers from the bed in case we had to abandon ship. While she did that I grabbed the fire extinguisher from behind the driver’s seat and ran back to the smoking tag axle.  I discharged the extinguisher through the small holes in the wheel in an attempt to cool off the disc brake caliper and rotor.  I got the wheel to quit smoking and went back inside to get the other fire extinguisher, just in case.

I left the engine running and started trying to figure out what to do.  My first call was to the Prevost Service Center in Jacksonville, Florida.  They could not help me directly, and their mobile service guy was off today, but the service manager gave me the name of someone to call in the Orlando area.  Long-story-short, I ended up getting passed off to a whole string of people, none of whom could help me but each of whom tried to connect me to someone who could.  No one could provide assistance in-situ and most places would not be able to help us for 1 to 2 weeks, if at all.

I talked to a guy in Cocoa, about 20 miles back the wrong way, who sounded like he could help in a week if we could get the bus there.  I eventually talked to our mobile mechanic, Joe Cannarozzi, who was in Michigan working on a coach near Lansing about 30 miles from our house.  I also called the Prevost Action Service System (PASS).  The Jacksonville service manager was not willing to tell me it was OK to lift the tag axle and drive on six tires but the P.A.S.S. technician thought it would OK as long as I did not drive too far and kept my speed down.  I eventually talked to Barry at JOSAM in Orlando, who could not help us directly but seemed genuinely concerned about our situation.  Barry ultimately put me in touch with John at Action Mobile Service on the south side of Orlando.  Both business were located near the intersection of the FL-528 Toll Road and FL-91 (Florida’s Turnpike).  That intersection was about 15 miles from where we were sitting on the side of the road.  The consensus opinion was that I should be able to complete the relatively short trip of 15 miles by lifting the tag axle and limiting my speed.  By the time I pulled back into the flow of traffic we had been on the side of the road for two hours and were more than a little bit rattled and frustrated.

Limiting my speed on a limited access highway posted at 70 MPH was not without its own risks, but it was (apparently) our only alternative unless we wanted to be put on a “low boy” and towed.  The sooner we got off FL-528 and into someone’s service yard the better.  Traffic was now thicker as it was 1:30 PM but I finally had an opening that was long enough to allow me to get up to 45 MPH without cutting someone off and give other vehicles plenty of time and distance to move over and go around me.  I kept my speed at 45 to 50 MPH, except where posted lower in a construction zone, of course, and kept my emergency flashers on the whole way.

We exited FL-528 at Exit 4.  When I started driving I was headed for JOSAM and Barry had given me a ‘heads up’ about how to navigate Exit 4 as this exit serves a dual purpose.  Staying to the right it immediately becomes an entrance ramp to FL-91 (Florida’s Turnpike) whereas staying left and going straight to the stop sign gets you to a side street that leads to FL-441 / Orange Blossom Trail to the right or to JOSAM to the left.  We were nearing Exit 4 when Barry called back and told us to go to Action Mobile Service.  Exit 4 was also the correct exit for Action Mobile but in the opposite direction from JOSAM.  It was at this point that we had a bit of confusion.

We were both already pretty frazzled by the events of the last few hours and the last minute change in directions did not make things better, especially with Linda handling the phone call and unable to hear well.  We had JOSAM’s address programmed into the Rand-McNally TripMaker RVND 7710 GPS, but that was no longer our destination.  Linda tried to enter the address of Action Mobile Service into the unit but it had become non-responsive.  I checked the power adapter and saw that the light was out so I knew the unit was not getting 12 VDC power and the battery had probably run down.  The adapter often works loose so I plugged it back in but it did not restore the power.  The two bottom outlets share a circuit and the two upper outlets share a different circuit so I plugged the adapter into one of the upper outlets.  I quickly determined that all four of the 12 VDC accessory outlets appeared to be dead and told Linda to stop trying to use the GPS.  She put the address in her phone instead but was having trouble with that as well and was slightly disoriented by this point.

I knew we had turn right at the stop sign because Action Mobile was “in the opposite direction from JOSAM.”  I also knew I needed to get onto Orange Blossom Trail, but was unclear as to just where that was or which way we needed to turn when I found it.  As it turned out I could see a street sign that indicated OBT was the cross street at the traffic signal immediately after we turned right at the stop sign.  We were where we needed to be, but now which way to go?  On a hunch, when the light turned green, I turned right and headed south.  Linda got oriented relative to the GPS/mapping information on her phone and eventually confirmed that we were closing the distance between our current location and destination and thus going in the correct direction on the correct road.  I turned left onto the Central Florida Parkway and then a short distance later turned right onto Satellite Blvd.  Action Mobile was the second business on the right but I pulled up along the curb, making sure I did block any driveways, and walked in to confirm that we were in the right place and find out where they wanted me to put the bus.

We were met by the Service Manager, John Provo, who pointed me to an open area where I could back the bus in and be out of the way.  We unhooked the car and Linda drove it into the yard and parked it near where the bus would end up.  I then swung the bus out into the oncoming traffic lane and made a hard right turn through the gate and into the yard.  (The tag axle was already up, of course.)  I pulled forward and then backed in towards the passenger side with Linda spotting for me.  I put the tag axle down so the drive axle would not have to support the entire weight of the rear end and checked for level.  We were level enough for comfort so I did not bother with leveling.  Once we were parked I went in to talk to John (the service manager, the owner’s name is also John).  He and I looked at the driver side tag wheel/tire and I described what had happened.  Other than the yellow powder from the fire extinguisher there was no visible evidence of what had transpired.

Owner John Douglass was outside talking to someone and Linda ended up talking to him.  In the course of their conversation she found out that his parents owned a house on Runnymeade in the same subdivision where we lived for 35 years.  Not only that, they were there when we were, and John lived with them for a while after trade school (diesel mechanics).  He eventually bought the house from them, again, all while we were there but we did not recall ever meeting.  It really is a small world, after all!

John D. (the owner) introduced us to Bill (the mechanic) who would be handling our repair first thing tomorrow morning.  There wasn’t much else to do at that point except to get comfortable, have a late lunch snack, and check in with “Smitty” (John Smith) at Williston Crossings, Pat/Vickie, Butch, and Chuck while Linda updated our children on the status of our situation.

The last employees left around 5 PM and closed/chained the gate.  We had the code for the lock but the lock was on the outside of the fence.  An employee returned around 6 PM so when he left I went out and put the lock on the inside.  It did not occur to me at the time that employees might have to get in at all hours for emergency road service calls, but I was willing to get up and unlock at whatever hour if needed.

It would be a while until our evening TV programs came on, and we still had plenty of daylight, so I got out my multi-meter to try and diagnose what had happened with the power supply to the four 12 VDC accessory outlets I wired up for powering portable accessories in the cockpit.  The 12 VDC distribution/fuse panel seemed like the obvious place to start.

The 12 VDC distribution/fuse panel is above the entry stairs from the cockpit landing up to the main floor.  It’s an enclosure that is installed against the ceiling and is about 10″ high.  It is in-between the TV box (DS) and the front A-C box (PS) and is about 28″ wide.  It has a door that is 7″ tall by 24″ wide and hinged at the top, opening out from the bottom.  When the door is open the actual opening is, of course, a bit smaller.  The hinges on the door do not hold the door open against the ceiling, so one of the challenges working in this space is keeping the door up and out of the way.  When working alone I usually prop it open but with Linda helping me she was able to hold it open with one hand and hold the multi-meter with the other hand while I handled the probes.  The other challenge is that it is above the stairs and just high enough that I cannot reach it easily without standing on a stool, which is what I did while Linda stood with her right foot on the navigator seat and her left foot on the main floor.  It was probably a strange sight if anyone noticed.

Each circuit has have a number tag on the wire where it connects to the fuse block terminal.  We are fortunate that one of the pieces of documentation we got with the coach lists all of these circuits in numerical order with a description of what it feeds.  I recalled (vaguely?) that I had disabled and/removed some devices a while ago and repurposed the circuits to supply power to the auxiliary outlets.  I found the circuit numbers and checked those and they did not have power.  I traced the problem back to a relay that did not seem to be operating correctly.

I carry spare relays and was going to replace it but discovered, after great difficulty removing the relay from its socket, that my spare relays were slightly different (4-pin instead of 5-pin).  I spent some time considering whether I could use a 4-pin relay, or perhaps just install a jumper wire to bypass it, when I realized that there were a few duplicate wire numbers, and that those duplicates were the very numbers with which I was working.  I checked for 12 VDC on those duplicate circuits and guess what?  No voltage there either.  I pulled one of the automotive style blade fuses and it was open.

I got the parts box with the spare fuses from the car and found a correct replacement.    I checked the other two fuses and they were also open.  They were very small, 2 and 3 A respectively, and I replaced them with 5 A fuses.  After reconnecting a wire (that I had already forgotten I disconnected at the beginning of this process) we finally had power restored to all four outlets, which, as I mentioned earlier, get their power from two different circuits, one for the upper pair and a different one for the lower pair.

We spent the night in Action Mobile’s yard.  Located in a light industrial area just off a major commercial thoroughfare, it was certainly not an RV park, but it was fenced, with barbed wire on top, had a locked gate (for which we had the code), and lots of security cameras.  Satellite Blvd. was surprisingly busy for a side street, with lots of trucks of all sizes and some hot rodders with booming car audio systems.  There was a large food processing plant directly across the street that was brightly illuminated and obviously in production 24 hours a day as there were lots of cars/trucks that left around 7 PM and a larger number that showed up at the same time and parked all along the building.

We had been running on inverters all day and I wanted to make sure the batteries were close to fully charged before we went to bed so I turned on the genset around 7 PM while we watched TV and tried to relax.  I used TVFool.com to locate OTA TV transmitter antennas.  Given that we were on the south edge of Orlando the towers were, not surprisingly, in all directions.  Most of the strongest stations, however, were lined up to our northeast so I pointed the front TV antenna in that direction.  We were able to pick up one of the PBS affiliates and watched a fascinating program of the Vikings; their journeys and reach, and the use of satellite imaging technology to identify possible archeological sites in what is now the Canadian Maritimes.

We had to be up at 5 AM so we were dressed and ready to go at 6 AM which is the time I was told Bill would be arriving.  I set two alarms and we went to bed around 11 PM.

2016/04/07 (R) Crisis Averted

It rained overnight and continued, off and on, this morning.  We were up around 5:15 AM, got dressed, and had bagels and orange juice for breakfast but I did not make any coffee.  Bill (our mechanic) was the first to show up at 6:45 AM.  Since the lock was on the inside of the gate I walked over to make sure he could get it open.  Just before 7 AM an ALSCO truck pulled in.  There were two other ALSCO trucks in service bays and the driver walked over there, came back a short time later, and then drove away.  Bill unlocked the office and then settled in at the outside picnic table.  I realized pretty quickly that nothing was going to happen with our bus until John P. (Service Manager) showed up, but that was OK.  It was a great comfort to be off the road in a safe place where we could sit for quite a while if needed and to know that there was a guy who had the skills and resources to fix our bus sitting were I could see him.  We also had a good feeling about John D. (the owner).

At 7:45 AM I received clearance to move the bus to the last service bay (farthest from the street) and by 8 AM had the engine running and the tag axle up.  Action Mobile Service has seven service bays, only one of which (#1) is inside.  The other six are under a large roof with open sides.  (It’s a Florida thing; you won’t see that in Michigan.)  They wanted me to back into the bay so I had to reposition the bus toward the passenger side, swing the nose to the left and into the entrance gate, straighten out, back down to the bay, and then swing the back end in on the passenger side.  Linda spotted for me, as she always does, and Bill signaled the final positioning.

Our coach at Action Mobile Service in Orlando, FL. awaiting the start of the driver side tag axle brake repair.

We were told yesterday that we would not be able to stay in the coach while Bill worked on it, but Bill said we could.  The difference was that because the tag axle can be lifted they did not need to jack up the bus.  That made for a more comfortable day, both for us and for the cats, and allowed us to be more productive than if we had been confined to the customer lounge.  I spent part of the morning in the customer lounge anyway as I was on the phone with Prevost Parts US in Elgin, Illinois.  I spent most of the rest of the day interacting with Bill and the two Johns.  Linda, however, was able to use her computer in the bus and work on tax returns.

The brake was locked up to where Bill could not turn it by hand but he got the caliper off somehow and then removed the hub and rotor.  I am always interested in how these things are done but figured that Bill, who did not know me, did not need me staring over his shoulder while he worked.  When he finally got everything apart he determined that the brake pads and rotor needed to be replaced, as did the wheel bearings, races, and seals.  The major problem, however, was going to be the disc brake caliper.

This is what a Prevost H3-40 tag axle looks like when it is completely disassembled.

Action Mobile called in Rex from Rush Trucking, a huge national trucking company.  Rex had a heavy duty truck parts business at one time but sold it and went to work for Rush.  He had been in the heavy truck industry for over 30 years and had a lot of expertise and contacts.  He looked at the situation and determined the part numbers for all of the parts Bill needed.  A couple of hours later he showed up with everything, including a rebuilt/remanufactured caliper.  The only thing he could not get was a new torque plate (spider).

We could not determine if a new torque plate was needed but it was a possible cause of brake misalignment.  If we were going to replace it, now was the time as it was completely accessible with the brake and axle hub removed.  Gary at Prevost Parts had spent a lot of time with me during the morning and been especially helpful but I ended up talking to Wes to order the spider.  It’s a phone bank and you usually have to take who you get as you cannot dial a specific person.  You can leave a message and request a callback, but that can take a lot longer than waiting on hold for “…the next available representative.”  They had a left hand spider in New Jersey and I ordered it for overnight delivery to Action Mobile.  It is supposed to be here by 10:30 AM tomorrow morning.

Without the spider Bill could not wrap up the job but he was able to spend the afternoon putting new seals and bearings into the axle hub and mounting the rotor to the hub.  Once the spider arrives, and assuming it is the correct part, he figured it would take 90 minutes to put everything back together.

The new rotor mounted on the hub (just behind the red stool, and the new caliper (upper right behind the cardboard box).

John D. (the owner) said we could leave the bus in the bay overnight.  We got to chatting and I gave him a tour of the inside.  He noticed that we were not running a generator and asked if we were on an inverter.  I confirmed that we were and he offered us the use of a 50 Amp RV outlet that was located by the passenger side rear of the service bay.  It turned out that there was also potable water available if we needed it.

I waited until Bill was done working at 3:30 PM, so as not to interfere with his work, and then got out the shorepower cord and plugged it in.  We do OK on the inverter, and can use everything with the genset running, but the coach is definitely most comfortable and useful when plugged in to shorepower, especially “50 Amp” (240/120 VAC) service.  Although it was warm today, the coach was partly shaded by the bay and we decided not to run the air-conditioners.  With the windows and roof vents open, and the exhaust fans on, our small Duracraft portable fan was sufficient to keep Linda comfortable.

By 5 PM everyone was done for the day and left, locking the gates on the way out.  We had the lock code in case we needed to get out, or let emergency services in, but decided when we first arrived that we would not come and go unless absolutely necessary.

I had a lengthy conversation with Chuck about the status of our brake repair and what I was finding out about Prevost and parts availability in the process.  I also texted some part numbers to Butch so he could pursue possible sources in northern Indiana and southern Michigan.  While I took care of those communications, Linda made salads and a potato lentil curry for dinner.  After dinner I talked to Pat and Vickie for a while and then called Butch and had a long chat with him.  Linda was watching (reading, CC)  our Thursday evening CBS TV programs and when I concluded my call with Butch I settled in to watch TV with her and work on my blog posts for the last several days.

2016/04/08 (F) Brake Away to WCRVR

I set alarms last night for 6:45 AM since Bill starts work at 7 AM and I told him yesterday we would be up and dressed by then and to not hesitate to work in/around our coach.  I made a small pot of coffee and we had orange juice and bagels for breakfast which was made easier by the 50A RV electrical service that John D. had offered us late yesterday.  There wasn’t much of anything Bill could do on our coach until the torque plate (disc brake caliper mounting spider) showed up.  Linda worked at her computer while I worked on blog posts on my iPad.

I eventually put aside my blog work and gathered up some of the boxes the new caliper and other parts were in.  I texted Butch with various part numbers I had been given by Prevost, gotten off of used parts, or copied from labels on boxes.  He called me just before 10 AM to let me know the number on the box label appeared to be the one we needed.  He was in contact with someone at ABC Bus Parts in Muncie, Indiana who was in contact with someone at Meritor.  The information he was getting was that the caliper was not available in stock but I could get it for $1,200 with a 45 – 60 day lead time.  While I was glad to hear that might be the case, it certainly contradicted everything I had been told by Prevost, which I found a bit disturbing.

The UPS truck showed up at 10 AM so I walked up to the office, retrieved the box, and took it back and set it by the driver side tag axle.  I had just talked to Bill at little earlier but he wasn’t around at the moment.  He still wasn’t around at 11 AM so I went to the office to see what was going on.  As I suspected, Bill had to go out on a mobile service call.  John D. (the owner) called Bill and then let me know that he would be back in about 10 minutes.  I made sure everyone knew that I wasn’t trying to create an unnecessary since of urgency or priority for our coach, I just wanted to know what the status was.

The new torque plate (spider) installed on the driver side tag axle. The new caliper is visible lower right. Action Mobile Service, Orlando, FL.

When Bill returned he got right to work and in short order had the new spider mounted.  He then installed the hub, the outer bearing, and axle seal.  The hub gasket and cap were last, after which he added hub oil through the hole in the sight glass portion of the hub.  It takes time for the oil to penetrate the bearings and settle so some patience is required to get the correct oil level.

With the hub installed Bill now had to get the caliper in place.  It’s both heavy and awkward to handle.  It has to be lifted into place, lowered around the rotor, and secured with a pair of large steel slide pins.  The problem is how to hold the caliper in place while getting the upper pin in place.  In order to accomplish that he had another mechanic help him.  He then adjusted the automatic slack adjuster and finally reconnected the air line to the brake “can” (actuator).

I left him alone until he was done and it was a relief to finally see that everything appeared to fit together.  The hub spun with the minimum required drag, but we still had to test the installation.   (The brake pads are always in contact with the rotor.)   To do that I needed to apply and release the brakes but the tag axle was up (lifted) which cuts off the air supply to the brake chambers.

Lowering the tag axle releases the air from the brake chamber that powers the lifting mechanism and at the same time allows air into the air springs that support the weight of the coach on the axle.  It also changes one of the air valves so that application of the brake pedal allows air into the tag axle brake chambers.  I could lower the tag axle, and probably apply the brakes once or twice, with the air stored in the system, but raising the axle back up, and/or additional application of the brakes, would require me to start the engine.  That required a few minutes of my time so Bill decided to take his lunch break.

The hub and rotor reinstalled along with the new caliper, ready for testing. Action Mobile Service, Orland, FL.

While Bill was eating lunch I checked with the two Johns to see if Rex could supply me with another left (DS) caliper and two right (PS) calipers.  They checked with him and he said he could have two of them this afternoon but could not get the third one until Monday.

When Bill was done with lunch I started the engine and lowered the tag axle which caused the driver side rear to drop as the tag wheel/tire was not yet on the hub.  When I applied the brakes Bill was not able to turn the hub and when I released the brake pedal he was able to turn the hub once again.  That was the best test we could do with the bus sitting still and Bill was satisfied that the problem was properly repaired.  Before Bill put the wheel/tire back on he climbed under the bus and greased the passenger side tag axle disc brake caliper.  When he went to put the wheel back on the hub was too low.  With the engine running I tried to raise the driver side rear using the Level Low system but it would not come up high enough.  I tried lowering the front to pivot the tag higher but that did not work either.

Bill found a length of 4″x4″ timber, put it in front of the outside driver side drive tire and had me move the bus forward just enough to roll the tire up onto it.  That raised the tag axle hub enough that he could get the wheel onto the studs and secure it.  As soon as it was on I moved the bus forward a little more until the drive tire was off of the 4×4.  The tag axle brake problem was fixed.  Bill greased the two front/steer disc brake calipers and then checked the oil level in both of those hubs and the passenger side tag axle hub.

Now that I knew the disc brake caliper and spider fit and worked properly I let John D. know that I wanted the three additional calipers.  He let Rex (Rush Trucking) know.  We did not want to hang around Action Mobile in the bus until Monday and given that I would have to come back Monday in the car anyway I indicated that I would pick all three of them up then.

I settled the bill for the repair work.  The amount was substantial but I knew what it was going to be so it wasn’t a surprise.  I also considered it fair and had no problem paying it.  A little over 48 hours before we come dangerously close to having our bus catch on fire and if it had it would have been completely consumed.  In the hours that followed we were faced with the very real prospect that we might not be able to get our bus repaired, effectively rendering it useless as a motorhome.  We even half joked about buying a lot in an RV resort, moving the bus there (towing it if necessary), and becoming Florida residents.  It was a real low point from which Action Mobile restored our plans and dream for a long, adventurous retirement using our motorcoach.

As a separate transaction I paid a 50% deposit on the three brake calipers.  At that point there was nothing left to do except say ‘thank you,’ hook up the car for towing, and leave, but not before calling Williston Crossings and making a reservation.

Linda usually handles the reservation/registration process but with her hearing and voice issues that has become my job, at least temporarily, but hopefully not long-term.  Sometimes we have to Ieave a message and get a callback, but Joann answered the phone this time.  We had decided that we wanted to stay through Tuesday evening and depart on Wednesday morning April 13.  To our surprise there was no pull-through site available for that set of dates.  Site #439 was available, however, and was actually our 1st choice anyway as it is next door to our friends, John (Smiity) and Ali, and is the same site we were on for our entire winter here in 2014.  I made the reservation, which was very easy as the resort still had our information on file.

With our camping arrangements made Linda texted Smitty to let him know we were getting ready to head his way.  I started the bus and pulled it out of the bay and around to the passenger side while Linda spotted for clearance to obstructions.  I pulled up by the office, lined up with the gate, and shut off the engine.  Meanwhile Linda brought the car up behind the bus and we connected it for towing.  We checked that all the lights were working and were ready to go.  We worked our way back the short distance to US-441 / Orange Blossom Trail via Satellite Blvd and the Central Florida Parkway.  From there it was only a little over a mile north to get back to the entrance to FL-91 (Florida’s Turnpike).  We had already studied the route on our iPad Maps app so we knew it was an easy interchange, with all turns to the right.  As long as we stayed to the right we would end up northbound on the Turnpike towards I-75 and Ocala.

Because I wanted to make sure I stayed to the right I ended up going through a manned tollbooth rather than the usual SunPass Only lanes.  The staffed lane was also marked for wide vehicles and was also a SunPass Lane, so it was not a problem.  It only caused a brief moment of confusion as the attendant started counting axles.  I pointed to our transponder but he did not see me and I pulled on through as soon as the electronic sign said “SunPass Accepted.”

Traffic on the Turnpike was not too bad but we did see an electronic information sign shortly after getting on advising of traffic congestion between the FL-301 exit and the I-75 merge.  No surprise there, especially on a Friday afternoon.  I rolled along initially at 62 MPH while Linda kept a close eye on the temperatures of the four wheels/tires that have disc brakes (steer and tag axles).  The DS tag was running hotter than the other wheels by at least 10 degrees F, including the PS tag; not enough to indicate a problem, but given our recent experience and with no meaningful miles on the repair work, we were understandably nervous.  I decided to error on the side of caution and travel at 55 MPH.

Linda checked the temperatures every few minutes for the entire trip.  The steer tires/wheels and the drive tires/wheels eventually settled in to temperatures in the mid-90 degree F range, plus or minus, while the tag tires settled in around 105 degrees F while free-wheeling and got as high as 120 after braking.  The temperatures came back down, however, which was important, and the passenger side was sometimes higher than the driver side, which either meant the driver side was working or the passenger side was starting to fail.  I preferred the former possibility to the later but it wasn’t like I had a choice.

As we were warned, the traffic on the Turnpike slowed to stop-n-go conditions starting at the exit for FL-301.  It remained congested, very slow, and often completely stopped all the way to the merge with I-75 northbound, where it got even worse (if that was possible).  The volume of traffic trying to move north was as astounding as its lack of movement and remained heavy all the way to exit 354 at Ocala where we finally left I-75 and headed northwest on US-27 towards Williston.

Linda had texted several status updates to Smitty and at 5:05 PM texted him again as we turned off of US-27 / Main Street onto NE 5th Street.  I stopped at the turn into the resort and lifted the tag axle before proceeding around the corner.  As I came around and pulled up to the gate Smitty was coming the other way in his golf cart.  We said a quick ‘hello’ and he opened the gate.  I pulled up by the office, which had closed just minutes before, so our bus/car combination was not blocking the incoming traffic lane and shut off the engine.  We unhooked the car and Linda moved it to a temporary parking spot.  John and I discussed how best to get me into the site.  I expressed my preferred approach and he agreed to try it.  I then followed him to the site where Linda was waiting for us.

I learned a lot about how to maneuver this bus two years ago from ‘Big Bill’ Cowick when we were parked next to him and Nancy  at Suncoast Designers in Hudson, Florida.  Smitty got me positioned correctly to start backing up and watched the front end while Linda watched the rear end.  I was able to back it up around the corner of an intersection and angle it towards the site, coming very close to a recently added street sign on the passenger side without hitting it.  Once the right front corner was able to clear the sign I turned the steer tires to the left, tightening the turn as I went, while watching John, Linda, and the concrete pad in my mirrors and rearview camera.  I backed the bus around smoothly onto the pad and then pulled forward once to make sure I was straight and the distance I wanted to be from the driver side edge of the pad.  I then backed up to where the tag axle tires were still fully on the concrete pad with only a foot or so to spare.  That positioned the bus conveniently for utility hookups while leaving plenty of space to open bay doors and lots of room on the passenger side where the patio area is located.  It also created plenty of space in front of the bus for the car, getting it well clear of the road.

Ali and John were already at Jeff and Kathy’s when John drove up to let us in.  With the engine still running and the tag axles still up I checked that both tag axle tires spun freely.  They did, which was very good news, so I lowered the tag axle, leveled the coach, and shut off the engine.  I disconnected the chassis batteries, turned off the auxiliary air to the engine accessories, plugged in the shorepower cord, and made sure the auxiliary air-compressor was turned on.  While I was taking care of all that Linda prepared a few things on the interior, opened windows and ceiling vents, and got a Yuengling lager out of the refrigerator and put it in an insulated cozy for me.  It was time to relax and go be sociable at Jeff and Kathy’s 5th wheel.

Everyone wanted to hear about our recent “adventure,” of course, and the telling of the tale fell to me.  At some point my beer was gone so I walked back to our coach and opened our bottle of Nutura Carmenere, a red wine I picked up at Publix in Cocoa Beach along with a Nutura Merlot.  It was not a brand we had tried before, and I had never heard of a Carmenere, but they were $11.99 per bottle wines on sale 2 for 1.  We are always on the lookout for red wines that I like (not dry, no tannins) and are willing to risk $5 to $8 to try one.  Not surprisingly, the Carmenere was drier than I like, but I was able to drink it and I got to show everyone one of our polycarbonate wine glasses.

We stayed and chatted until 7 PM when everyone was finally hungry and we all returned to our coaches to have dinner.  After dinner I sent a brief text message to four people just to let them know that we made it to Williston without any difficulties and that I would fill them in on details tomorrow.  We were planning to go next door to John and Ali’s 5th wheel after dinner and sit around a campfire but we did not see them outside and we were very tired.  I aimed the front TV antenna towards Gainesville and we found something to watch.  Linda was off to bed before 10 PM and I was in bed by 11.   It had been a long day and we were glad to have it behind us and be back at WCRVR.

2016/04/09 (S) Water Pump Down

In spite of being very tired I stayed up late last night watching back-to-back episodes of Ken Burns’ JAZZ.  Linda went to bed around 10 PM and I turned in at 12:45 AM.  She was up at 7 AM and walked to the bath/laundry building to take a shower while I slept in until 8:30 AM.  I was going to walk over and get a shower as well but Linda informed me that the water never got more than lukewarm.  No thanks.  I decided to hang out in my sweats for a while, made a pot of coffee, and worked on my blog posts for the past week.  With all that has happened I have had quite a bit to write about.

I plugged our WiFiRanger in last night and it did not have any difficulty connecting to the resort Wi-Fi system.  The problem we seemed to be having this morning was that our devices will not stay connected to the WiFiRanger.  Nuts.

Linda needed to continue working on taxes and set her computer up on the desk.  I have not taken my computer out of its case since I packed it up on Wednesday morning but I will have to get it out sometime soon.  Our fresh water level finally dropped below 1/3 tank so I will need to hook up the water softener fairly soon but decided I would do the laundry and get a shower first.  I gathered up all of the soiled clothes, towels, and some of the bedding, along with the tote bag of laundry supplies and the tote bag of shower supplies.  I loaded everything into the car and drove to the north laundry/shower building, which is better equipped than the one near our site.  It was noon.

No one else was using the laundry so I used three of the washing machines closest to the dryers.  These washing machines take about 25 minutes to run through their cycle so it was just over half an hour before all three loads were done.  The dryers run for about 45 minutes, so once I had the laundry transferred to the dryers I took a shower.  I then drove back to our coach, dropped off the shower supply bag, and we stripped the bed.  I returned to the laundry building, washed the sheets, and transferred them to a dryer.  As each dryer load finished I moved it to a large table and folded or hung it up.  By 3 PM I had everything neatly packed back into the nylon mesh laundry bags and returned to our bus.

Linda helped me get the laundry inside and put away.  I then turned my attention to refilling our fresh water tank.  That is a bit of a process as I have to get out the pre-filter, with hoses and pressure regulator attached, and the water softener, again with hoses attached.  Heavy, bulky, awkward, etc.; it’s my second least favorite RV chore, right behind checking tire pressures. I got everything connected and turned on the water supply.  The connection at the supply faucet and the connection at the coach inlet both leaked badly.  I snugged up the coach inlet connection so it didn’t spray water.  It was still dripping quite a bit but it was good enough for filling the tank.  I opened the fill valve, heard the water flowing into the tank, and opened the door to have a look.

The remote gauge had dropped below the 1/3 tank level a day or so ago so all we could tell from the house systems panel was that we had less than 40 gallons in the tank.  I had noticed this morning that we were not getting the usual flow of water to the toilet and Linda tried to use the kitchen faucet late this morning and got no water.  Although I did not think we had used that much water we both made the (naïve) presumption that we had run the tank dry.  To my surprise (not really), the tank was at the 1/4 level, which meant it still glad about 30 gallons of water in it.  That seemed to suggest rather strongly that the problem was something connected to the water pump.  Not good.

I shut off the water and started grousing, because I find that it makes me feel better and is part of my problem-solving process.  So does swearing a bit, so I did some of that too.  Not like a sailor, of course; I was a USAF ROTC cadet years ago, after all.  There were a few obvious things to check, after which I figured I would call Butch if they didn’t pan out.

I got out my multi-meter and then looked up the circuit numbers for the water pump and switch circuits.  I checked those circuits in the 12 VDC distribution panel and they all had +12.7 VDC which meant the fuses were OK.  The power to the pump is switched through a relay so that the pump can be turned on/off from multiple locations using momentary contact switches.  The easiest way to check the proper operation of the relay and confirm/deny the presence of power at the pump, was to disconnect the + 12 VDC and return wires from the pump and check for voltage on the supply wires.  With the relay “off” there was no voltage present (a very small mV reading).  With the relay “on” I had 12.7 VDC.  Relay off, no voltage.  That pretty much meant the water pump was down.

While not a crisis situation, this failure, at this time, and on the heels of all of our other recent problems, was certainly unwelcome news (not that any failure at any time is ever welcomed).  The only upside was that we were at a nice RV resort with full hookups, in a familiar location with relatively convenient access to resources, and in the company of friends.  We had city water available, so we could use all of the systems on the coach that required fresh water, and we were scheduled to be here for four more nights, which meant I had time to deal with the problem, including getting parts shipped here if needed.

My first instinct, however, was to try to get this fixed RIGHT NOW!  I called Smitty to see if there was any place in town that sold RV parts.  As I expected, he directed me to the local ACE Hardware store.  I knew from previous visits that they carried some RV parts but were unlikely to have 12 VDC water pumps, and even less likely to have the exact model I wanted/needed.

Linda did a Google search and located a Camping World store in Summerfield, Florida south of Ocala.  Not that I was eager to go to Camping World, the home is “list price plus,” but if they had the right pump (or any pump) in stock I was feeling like it would be worth paying the premium to get it and have the problem resolved quickly.  Unfortunately (or fortunately), it was already 4 PM and the store closed at 5 PM.  There was no way I would make it in time, so I returned my attention to making the coach usable from the city water supply.

In order to operate off of the city water supply we would need to leave the water turned on, and in order to do that I needed to get the connections to not leak.  While I probably had replacement washers in one of my parts boxes, I decided to go to ACE Hardware for washers just on the chance that they might have an appropriate water pump.

The only pump at ACE that would have worked was a 120 VAC unit and I was tempted to buy it.  In fact, when I redo the water bay I will install redundant water pumps and I am seriously considering keeping the 12 VDC pump and making the second one a 120 VAC model.  For now though, replacing the DC pump with an AC pump would involve more work than I wanted to get involved in.  I did find what I was really looking for, however; garden hose washers.  I bought two different kinds of flat washers, vinyl and rubber, and a pack of vinyl strainer washers.  I should have also bought a roll of Teflon tape, but I did not think of it at the time.  Back at our rig I realized that I was probably going to need Teflon tape.  I was sure that I had some but it was not in any of my four tool boxes.  Linda helped me empty out the car until we finally found the correct parts box.

I replaced the strainer washer in the pressure regulator fitting that attaches to the water supply as the existing one was damaged and badly deformed.  I also wrapped the supply faucet threads with Teflon tape before attaching the regulator to the faucet.  With the output of the regulator valved off I turned on the water supply.  Voilà; no leaks!

The strainer is the first line of defense against particulate matter getting into the regulator and clogging it.  When I redo the water bay, plan to set up the plumbing so that the supply water goes through a particle filter before going through a backflow preventer (check valve), an adjustable regulator, a water softener, and additional filters, all of which will be installed in the bay but easily accessed and serviced.  I might even install an inline UV sanitizer.  The only thing I will need to do to connect the coach to a water supply will be to connect a hose at both ends.  Priceless.

The other leak was at the fitting in the bay where the hose gets connected.  These garden hose fittings are cheap, easily deformed, and prone to leak, and I think they are one of the other “weak links” in the materials and systems used to make RVs.  (Sewer hoses and connectors are probably the worst, but that problem has been solved by Lippert Systems and I will be using their technology when I redo the utility bay.)  Replacing the flat washer periodically is necessary routine maintenance but easily overlooked until a problem develops.

I replaced the existing flat washer with one of the vinyl ones and then taped the threads on the (male) end of the hose with Teflon tape.  I carefully threaded the two pieces together finger tight and then just a little tighter with a pair of slip pliers.  (Over tightening actually deforms the washer and causes it to eventually leak.)  I opened all of the intermediate shutoff valves and Voilà; again, no leaks!  Our coach was now usable and we could leave the water on unless we were both going to be away from the coach for an extended time, when even a small leak could quickly become a big disaster.

Time to relax.  John and Ali were already down at Jeff and Kathy’s and Linda already had a Yuengling lager in an insulated cozy ready for me.  We took some peanuts along and walked the short distance to their site to sit a spell and visit.  Earlier in the day Jeff and Kathy had gotten a new dog and Kathy was out walking it.  They lost their Yorkie, Teddy, to cancer back in December and were not really planning on getting another dog so soon but an elderly gentleman, who lives alone in the resort, had a 3-year old dog that he was no longer able to car for and needed to find a home for it.  The dog’s name is “Mandy” and she is an 8 pound Dachshund / Miniature Poodle mix.  She has a Dachshund body size/shape and face but a silver gray, slightly wiry coat unlike any Dachshund I have ever seen.  She was friendly and sweet tempered and from all appearances she will settle in with Jeff and Kathy very easily.  While dogs get strongly attached to their owners, they also respond quickly to the kindness of strangers.

I think we were there for at least 90 minutes, perhaps two hours, before everyone got hungry and returned to their rigs for dinner.  By that time it was already 7 PM and we were headed to John and Ali’s 5th wheel once we ate, so Linda made a quick, easy dinner consisting of a nice greens salad and Amy’s Asian Noodle frozen/microwaved entrées.

After dinner I called Butch and brought him up to speed on our disc brake situation and told him about the water pump.  He and I shared the opinion that it seemed like something might have happened with the +12 VDC power supply to the coach.  Most of the house DC power circuits and systems, however, appeared to still be OK.  He reminded me that we have an Amazon Prime account and could probably get a new pump delivered to the resort by Tuesday for a much better price than at Camping World.  Roger that.  I let him know that our current plan was to leave WCRVR Wednesday morning and arrive at their place in Twelve Mile, Indiana on Friday.  He said we should go ahead and park and plug into the electrical power if they were not there as they would be setting up for a local hamfest that evening over at the county fairgrounds across the road from Bill Tharpe’s place in Mexico, Indiana.  Been there, know how to find it.

We walked next door to John and Ali’s around 8 PM and I took another Yuengling with me.  It’s been that kind of week, I guess.  They have an elevated propane firepit, conveniently located under their patio awning, and had chairs arranged around it in a conversational grouping.  We sat and talked until 10 PM, when John had to make the rounds to close up certain buildings and check the gates.  We continued to chat with Ali while John took care of his chores and he was back within 30 minutes.  By 11 PM Linda was finally too tired to be sociable, went back to our coach, and went to bed.  I stayed until almost midnight and finally left when I was yawning more than talking.  I went to bed fairly directly and went right to sleep.

2016/04/10 (N) Water Pump Prime

We got up this morning when we were ready and not a minute sooner.  I made coffee using the two new bags we bought at the Sunseed Co-op in Cocoa Beach.  I requested pancakes for breakfast and Linda obliged by making some very good ones.

Last night I was thinking about driving to Camping World in Summerfield, south of Ocala, today to buy a new water pump.  The store opened at 11 AM and I figured I would find a pet supply store and buy some cat food while I was out.  After Butch suggested last night that I could probably find the exact pump I needed through Amazon, I searched for it and he was right.  I ordered it with four hours to spare to qualify for next day delivery with an $8 upcharge so I would have it on Monday.  Standard Amazon Prime 2-day free delivery would have had it here on Tuesday, but I did not want to risk having it show up late in the day or worse, having the delivery truck get here after the office closed or not get here at all.

I had hoped to spend some time at my computer working on the blog but the best I was able to do was get it turned on, connect it to the Internet, and download my e-mail, which I had not done since Wednesday morning.  I was more than a bit surprised that I had over 80 MB of attachments!  The bulk of that was several very large photo files from our daughter having to do with some recent projects our grand-daughter Katie was involved in.

I called Chuck around 1 PM and caught him standing in line at a Cracker Barrel restaurant.  We chatted briefly while he and Barb waited to be seated and I filled him in on the latest developments in the Prevost air disc brake saga.

We had an early dinner after which we emptied out the car and the passenger side of the front bus bay to rearrange where things were stored and make room for the three new air disc brake calipers and the old one.  Linda brought the bathroom scale out and we weighed the old one as best we could.  I would have sworn it was 100 pounds but the scale said it was only 63 pounds.  That was good as four of them would only put 250 pounds in the car instead of 300 to 400 pounds.

We were able to repack the bus bay better and more quickly than I expected.  We put smaller, lighter boxes back in the car, got our beverages, and walked down to Jeff and Kathy’s 5th wheel for happy hour.  Jeff’s brother, Mark, was there and we learned that he lives in an apartment over by the Williston airport.  Jeff made hamburgers for everyone (except us, of course) and we stuck around while they ate dinner.  Jean showed up not long after everyone was done eating and joined the conversation.

Smitty had to lock all of the gates at 5 PM so I rode along while he made his rounds.  Linda and I left around 7:30 PM, as the light was just starting to fade, and went back to our coach.  We had a light dinner/snack of pretzels and hummus and shared a very delicious orange.  I called Butch and chatted briefly with him about the water pump and brakes and our revised travel plans.  As things now stand we plan to leave here Wednesday morning and get to their place in Twelve Mile, Indiana sometime on Friday.

At 8:15 PM we walked next door to John and Ali’s 5th wheel and sat around their propane firepit.  Smitty had made popcorn with peanut oil and Hawaiian sea salt.  Yum.  John had to lock up the resort buildings at 10 PM.  Linda and Ali were both tired and ready to go in for the night so I rode along with John.  Once we were back we retired to our respective rigs for the evening.  Linda was watching Elementary on TV so I picked up the story line in progress.  When it was over at 11 PM we went to bed and went right to sleep.

 

2016/03/21-23 (M-W) Webster Cape-Canaveral Jetty-Park Recovery

2016/03/21 (M) Webster to Cape Canaveral

I was up sometime before 8 AM after a less than completely restful night’s sleep.  Yesterday was our last full day at Florida Grande Motor Coach Resort (FGMCR) in Webster, Florida and today was departure day.  I am always a bit anxious when the time comes to move the bus after sitting for a while, and even though we have only been here for two weeks it has been a lovely, comfortable place to base camp.  Although we only had about 100 miles to travel today, I was more anxious than usual because of a combination of factors.

At the top of the list was the tag axle brake issue.  While I was hopeful that Joe had taken care of it, at least for now, we would not know for sure until we moved the bus.  Another big factor was that Linda has been very ill for the last few days and was still not well this morning.  That meant I would have to do more of the work of preparing the bus for travel.  I didn’t mind, of course, I just did not want to overlook something that was normally part of her portion of the departure routine.  The third, forth, and fifth factors were:  3) using our new SunPass transponder for the first time; 4) taking the bus on the Florida Turnpike and Toll Road system for the first time, and; 5) traveling a route that came into the Orlando area from the northwest and swung around the southern edge before heading straight east towards the Atlantic ocean.  The sixth and last factor was our destination, which was not a motorcoach resort with wide, straight roads and big sites, but rather a county park with narrow, twisty roads, closer sites, and lots of trees.  Charming, but not necessarily “big rig” friendly.  I knew, because I had visited Pat and Vickie Lintner here two years ago.

We had a reservation at Jetty Park Campground on Cape Canaveral where our GLCC friends, Pat and Vickie Lintner, have been since mid-February.  We had reservations starting today and running through the 28th, with departure on the 29th unless we decide to extend our stay and there was a site available.  Check-in time was 2 PM and our mapping app indicated 104 miles and a little over two hours for our preferred route.  Based on that we wanted to pull out of FGMCR sometime between 11 AM and noon.  That gave us most of the morning to prepare the bus for travel, and that was comfortable even with Linda being ill and not able to do as much as usual.

I did not have coffee this morning—I never do on travel days—and we just had a couple of pieces of toast early for breakfast.  In spite of not feeling well Linda got most of the inside of the bus ready to travel and even swept the floor.  I packed up our computers and iPads and then prepared the outside stuff.

The biggest, most time consuming job, and my least favorite, is checking and adjusting tire pressures.  I had plugged in the TireTrakker TPMS repeater last night and I turned on the receiver/monitor this morning after letting it recharge overnight.  It eventually acquired temperatures and pressures from all 13 tires.  The temperatures were all in the 60’s so I knew the pressure readings were current rather than left over from our previous trip.  The sensors are not accurate enough, however (in my opinion), so I checked all of the tires with my tire gauge except the mini-spare in the car.  The passenger side steer tire on the bus needed an extra 2 PSI, but all four tires on the car were low and needed to be increased.  So did the car spare, but I was not about to empty out the back of the car to get to it.  I should have taken care of this sometime during the last two weeks as the pressure was low enough to keep triggering an alarm on the monitor, and was not at the correct pressure for use should we need it.

By 10:30 AM we were ready to go except for disconnecting the shorepower and hooking up the car.  I was going to reposition the coach so we could hookup the car at the site and then exit to the left but a landscaping crew showed up, parked along the other side of the road to our left, and unhooked their trailer.  I was not going to ask them to move, and I doubt that they would have even if I did.  It was easier to just exit to the right anyway and hook up the car at the staging area by the clubhouse where we unhooked when we came in, so that’s what we decided to do.

At 11:20 AM I disconnected the shorepower and stowed the cord.  Chassis batteries ON; engine accessory air supply ON; inverter operating; main engine start; no problem.  I let the suspension and brakes air up on low idle as Joe had suggested and then pulled up the tag axle.  Linda moved the car to the empty pad across the street to the right and watched as I pulled out.  Once I cleared the turn I put the tag axle back down and Linda followed me counterclockwise around the front “pond” to the staging area where I shut off the engine and she pulled the car up behind the bus.  Many (most) RV parks have “no engine idle” rules.  There isn’t one posted here, and the staging area is far enough from the clubhouse and the closest sites that our engine would not have bothered anyone, but since we would be hooking up the car directly behind the engine we did not want to listen to it while working.

No less than three people stopped to chat with us while we were hooking up the car for towing.  That actually violates good RVing manners (unwritten rules) but they were just curious, being friendly, and/or wishing us safe travels.  The problem is that you are engaged in a critical process and anything that distracts you can result in overlooking something with potentially serious, even disastrous, consequences.  We are experienced enough at this point, however, to double check everything before we drive away, especially if we have been interrupted.  This time we backed the car up until the tow bar arms locked in place and then secured the air line and electrical cables so they would not pull loose.  Linda remained outside to do the light check while I started the bus engine and operated the controls.  Everything checked out and once Linda was back on board we were ready to go.  She had entered our destination into the GPS unit before we pulled out of our site.

Pat & Vickie Lintner’s site at the Jetty Park Campground, Cape Canaveral, FL.

As I pulled around to the exit gate the gatehouse attendants saw or heard us and opened it.  We got big smiles, waves, and “safe travels” from them as we left.  It was 11:50 AM.

The GPS routed us the same way we had determined using our iPad mapping apps.  We turned left out of the resort onto CR-478 headed east.  The road curved around to the north about four miles later and ran up to the town of Center Hill where we picked up CR-48 eastbound.  A half mile later the road turned northeast and a couple miles up the road the GPS told us to turn onto CR-704 (FL-?).  I had just started the turn when I saw the weight restriction sign; nothing over 28,000 pounds GVWR permitted! What the?!!!

I stopped soon enough that I was able to turn back onto CR-48 without having to back up, after traffic cleared, so we caught a break there but were both a bit unnerved by the failure of our Rand-McNally TripMaker RVND 7710 GPS to route us correctly.  It then occurred to me that the very small update I Installed last night might have reset the vehicle configuration as I vaguely recalled this happening once before.  Why R-M would design their GPS unit so it loses configuration data as a result of an update is beyond me, but there are several things about this unit that defy common sense.

Linda used her cell phone to try to figure out where we were now headed and determined that we could still get to where we needed to be.  She then opened the preferences screen on the GPS unit and found the configuration screens.  Sure enough, it thought we only weighed 20,000 pounds (we are closer to 42,000) and were only 12’6″ tall (we are probably 13’1″).  I really fault R-M for this as it creates a potentially dangerous situation.  Anytime the settings are changed, certainly if they are reset as part of an update, the unit should display a message to that effect and not allow the unit to be used until it is acknowledged.  Better yet, I don’t understand why the configuration should be changed as part of the update process.

At some point we turned left onto US-33, which seemed wrong, but Linda verified it was correct.  We ended going south on US-27 all the way back to Clermont and then getting on the Florida Turnpike (FL-91) headed south towards Miami.  We made it through the first Toll Plaza with an “OK to Proceed” sign, so we knew that the new transponder was working, which was a big relief.  The lane guidance feature of the GPS unit worked well and we did not have any difficulty negotiating the interchanges.  Linda kept an eye on the tire sensors throughout the trip.  All of the tires indicated temperatures in the 60’s except the driver side tag, which was 90 to 102.  It was definitely elevated, but not enough to be an immediate problem.  This was not unexpected as I knew that the new pads were dragging more than on the passenger side.  Interestingly, the pressure in that tire had not risen disproportionately higher than any of the other tires, indicating to me that it was probably the valve stem that was warmer due to its direct contact with the wheel, rather than the rubber of the tire, which was getting plenty of cool air blowing around it.

We arrived at Jetty Park at 2:15 PM, only 10 minutes later than our original ETA before we had to detour around the weight-restricted road.  Our name was not on the list (sigh) at the entrance gate but we were given the gate code and directed to the campground.  I found a place to pull up and shut off the engine while I went in to register us, as Linda had effectively lost her voice.  We were not on the list (double sigh) there either (same list, I suspect) but they found us in the computer.  I had confirmation e-mails, if needed, but had not brought them in with me.  We unhooked the car and parked it at the office.  We drove the bus around through the narrow, curvy gravel roads but I was able to make all the turns, even with cars parked near the edges, so the road system here is laid out better than it appears.

Jetty Park is a county-owned and operated public park and beach with a campground that has been turned over to the Cape Canaveral Port Authority to manage.  It is in a premium location in Cape Canaveral, Florida just north of Cocoa Beach and just south of the Kennedy Spaceflight Center and Cape Canaveral Air Force Station.  It is on the south side of the shipping channel that connects Port Canaveral to the Atlantic Ocean.  Cargo ships use this port/channel, but the main attractions are the Disney and other cruise ships and the U.S. Navy Trident submarines.  In addition to all of its other charms, it is one of the best places from which to watch rocket launches, and there is one scheduled for tomorrow night!  I think this is the first time we have stayed in a county park with the motorcoach.  It is more like a state park than the private RV parks and resorts where we usually stay.  It’s probably closest in appearance and feeling to a nice KOA.

Pat and Vickie saw us drive by and walked down to watch while Linda helped me back into site #343, a full hookup, 50 Amp site with nice trees around it.  I could not back far enough into the site to get the front tires onto the concrete pad due to low branches at the rear of the site.  As a result we were slightly low in front.  That would not normally be a problem but the Level Low system would not adjust the front end.  I have a spare air leveling solenoid and might have to work on this while we are here.  Ugh.  I took a picture on my phone and e-mailed it to our son and daughter.

Site #343, our first (of many) sites at JPCG (on right, beyond the trailer. Cape Canaveral, FL.]

I did not plug in the shorepower cord as I wanted to let the house batteries discharge to 24 VDC (50% SOC).  Linda and Vickie searched online for medical clinics.  Linda selected one about three miles away in Cocoa Beach and I drove her there.  It took about two hours from the time we arrived until she had her prescriptions.  We went to the CVS Pharmacy across the street to have them filled.  They would not be ready for 2 to 2.5 hours so we went back to the campground so Linda could rest as comfortably as possible.

Back at our rig I got our Wi-Fi Ranger connected to the park’s public Wi-Fi system and got our iPads and my computer online.  I did not set up Linda’s computer as it will likely be a few days before she is in the humor to use it.  I checked e-mail and the throughput appeared to be usable, if somewhat slow.  I suspect it will be better between midnight and 8 AM, but that is not when I tend to be up.  If we have updates, however, or I need to upload or download are files to/from BCM, I might adjust my schedule.  The RV life requires agility.

I left at 6:30 PM and drove back to Cocoa Beach to pick up Linda’s prescription medications.  I stopped at a Publix supermarket first and bought various groceries before going to the CVS Pharmacy.  On the way back I stopped at a Dunkin Donuts for a coffee for me and finally got back to our coach at 7:45 PM.  Linda helped get the groceries inside and then took her first dose of meds.

I turned the front TV antenna towards Orlando and rescanned for channels.  The TV found at least 60, including CBS and two different PBS affiliates.  I pointed the rear antenna in the same direction and rescanned the rear/bedroom TV but the scan would not compete successfully.  I tried it a couple of times with the same result each time.  Arrrgh.  When in doubt, do a power-off power-on reset, right?  I unplugged the power from the antenna controller and the TV set, waited long enough for any power capacitors to bleed down, and plugged them back in.  I pointed the antenna again and then scanned for channels.  Eureka, this time they were all there!  I should have tried that while we were at FGMCR.  Doh!

We watched our usual Monday night TV shows on CBS plus a few minutes of news and weather and then went to bed.  Given how Linda felt and was still coughing I figured neither of us was going to get a good night’s sleep, but we were both tired and there wasn’t anything else to do except try.  An overnight low of about 50 degrees F was expected so I had closed the roof vents and left the windows open just a crack.  We were still operating off the house batteries and inverter so I did not turn on the usual night lights.

2016/03/22 (T) Jetty Park Atlas

Linda had a really bad night last night, maybe the worst yet since she took ill, with persistent extended episodes of painful coughing.  She was obviously uncomfortable, and no doubt also frustrated, as she was finally able to start taking medication last night at 8 PM.  She was already wrung out and very tired, and I was a bit spent myself after the day we had yesterday, but neither of us got a good night’s sleep.  Today will need to be an easy day, of necessity, and we will need to rest so we can be up and alert late this evening for the rocket launch.  An Atlas V (5) launch is scheduled from the Cape Canaveral Air Force Station at 11:05 PM this evening.  It is a resupply mission for the International Space Station.

I got out of bed at 7:15 AM and fed the cats.  I was not well-rested, and would like to have gotten back under the nice warm covers, but I was also uncomfortable and had spent as much time supine as I cared to for one night.  The outside air temperature overnight got down to 51 degrees F but we closed the roof vents, and only left the windows open a crack, before going to bed last night so the inside temperature only dropped to 65.  I did not plug in the shorepower cord when we got here yesterday so I could not use the electric heater pad on the bed, but we had plenty of covers (and cats) to keep us warm and I did not need the extra heat.  I put on my sweats this morning, and was very comfortable.

Linda got up around 7:45 AM to take her medications.  She needed to heat a cup of water to make a salt water gargle mixture but the house batteries were down to 24.0 VDC.  That is roughly a 50% SOC (State Of Charge).  Lead acid batteries, including AGMs, can be discharged a bit more than that but it shortens the number of times they can be cycled so I do not like to let them go much below that level.  I took a few minutes to plug in the shorepower cord and soon enough we had 240/120 VAC power to the coach.  After Linda prepared her gargle mixture I rearranged the kitchen counter and then made coffee and got our vitamins and juice ready.

Linda tried to play a few games on her iPad while I worked on the drafts of my blog posts for the last two days and started the one for today.  Pat and Vickie were out walking and stopped by to see how Linda was doing.  I walked over to the office at 11 to register/pay for the next 7 nights of camping and walked past site #352 on the way.  It was still occupied, but the current occupants were clearly in the final stages of vacating the site.  I walked past the site again on my way back from the office and the current occupants were just pulling out.  When I got back to our coach I let Linda know it was time to move.

We walked over to the new site to scope out where to put the car and how to approach getting the coach backed in and then walked back to our current site.  Linda closed the front windows and secured a few loose items, but mostly left everything sitting right where it was as we were only going for a short, easy ride.  I turned off the Aqua-Hot electric heating element and then took care of the outside stuff.  I shut off the shorepower, disconnected the cord, and stowed it away, once again wishing that I had a cord reel.  I turned on the chassis batteries and engine accessory air supply, and started the engine.  While the engine idled and the chassis aired up Linda drove the car to the new site, parked it, and awaited my arrival.

Moving the coach from site #343 to site #352 was a simple matter of driving counterclockwise almost all the way around Red Knot Circle, the easternmost loop of the campground, and pulling into Siskin Drive headed east.  The location of trees and a light pole made for a tricky spot to get into.  The guy in the site to our east (driver’s side) offered to move his truck but I determined that it was not really in the way.

I lifted the tag axle to shorten the turning radius of the bus while maneuvering through the campground.  The drive was easy but it took a little bit of back and forth for Linda to get me backed in and centered on the concrete pad.  The trees at the back of the site were trimmed up high enough that I could back the coach in far enough to just get the steer tires onto the pad.  That was important as the pad was level enough that I did not need to adjust the leveling of the coach, which was a good thing because yesterday the front end portion of the Level Low system would not work.  I got out of the coach a couple of times to check the location of the tires and tree limbs and was pleased to see that the tag axle tires were actually off the ground.

I shut the engine down and we went through a modified arrival routine.  As usual, I shut off the chassis batteries, closed the air supply valve for the engine accessories, plugged in the shorepower cord, and put power to the coach.  The Magnum 4024 inverter/charger worked fine yesterday and it worked fine again today.  I do not know what caused the fault on the drive up from Arcadia to Webster, but resetting the unit seems to have restored it to proper operation.

The beach at Jetty Park & Campground looking south at Cocoa Beach, FL.

Linda got out the door mat, patio mat, our two bag chairs, and our plastic side table.  She also got the tire covers out of the car and put them on the bus.  I got out the windshield covers and the Little Giant step/extension ladder and set it up.  I retrieved the rivets to hold the lower windshield wipers off the glass and then Linda handed me the windshield wiper covers.  I wanted to put these on first to protect the windshield cover from getting snagged on the metal edges of the arms and wiper blade inserts.

This was the first time we have put the new windshield covers on since we got them two weeks ago so we had to figure out the easiest way to do it, or at least a way that worked. We positioned the large one-piece windshield cover behind the lower wipers and above their drive shafts.  That supported the fabric while I pulled it up under the upper wipers and attached the upper center snap and the lower driver side corner snap.  I repositioned the ladder to the driver side front corner of the bus, pulled the fabric up, and attached the driver side upper corner snap.  I moved the ladder to the passenger side front corner of the bus, pulled the fabric up, attached the upper corner snap, and then the lower corner snap.  I had to stretch to reach the upper snaps, so next time I will make the step ladder a little taller.

There are three covers for the passenger side: one for the door, one for the window above the door, and one for the window behind the door.  These are all small enough that there was no particular difficulty attaching them.  The trick was to start at the top and attach as many snaps as possible before climbing down and repositioning the ladder.  For the one large driver side cover I started with the upper center snap, then attached the upper rear snap.  I moved the ladder forward and attached the upper front snap and then did the three bottom snaps. When we were done with that we were finally free to relax.  Vickie and Linda discussed walking the park and Linda suggested starting between 3 and 3:30 PM.  I gathered she was finally feeling a little better, or was just sick and tired of being sick and tired.

At 2 PM Linda asked me get her some more tissues and sore throat spray.  I headed for the CVS pharmacy but ended up at the Publix supermarket, which is closer by a mile or so.  Besides liking Publix, that meant less traffic to deal with.  Somewhat like the Florida Keys, but not as extreme, we are on a long, skinny island with one main road running along its spine.  Unlike the Keys, there are more side roads and an occasional causeway that goes over to Merritt Island and on to the mainland.  I found what I needed at Publix and was back at the park in due course.

At 3:30 PM we went for a stroll around the campground and park with Vickie as tour guide.  After our stroll Linda was hungry and heated up some Amy’s Tomato Bisque Soup (vegan).  I was really tired and laid down in bed to take a nap that lasted over two hours.  When I got up I had the rest of the soup and a large green salad.  We then watched out usual Tuesday evening CBS TV programs but did not get to see the last 15 minutes of Limitless as Vickie texted to jet me know they were on their way over to fetch us and walk to the shipping channel to watch the rocket launch.

The Atlas V resupply mission for the International Space Station lifted off from the Cape Canaveral Air Force Station right on schedule at 11:05 PM.  The launch pad was much farther away from our position than the one used for the military satellite launch two years ago, but was illuminated by multiple light sources producing beams and shadows projecting up and highlighted by the clouds.  For all the launches Pat and Vickie have seen from this park, this was the first time they recalled seeing these lights.

Even though the Atlas V was a much larger rocket than one I saw two years ago, it was not as loud or as visually impressive as the other one.  There were scattered clouds at liftoff, which made for interesting viewing, but the rocket was fairly quickly above them and then disappeared from sight.  I tried to take a few photos, but I did not bother bringing the tripod or spend any time ahead of time figuring out appropriate camera settings.  I did, however, spend a few minutes playing with manual adjustment of the ISO setting.

A man sitting next to me was monitoring mission control on a radio so we knew what was going on before, during, and after the launch.  Only minutes after liftoff the rocket had burned enough fuel to reduce its weight by 75%, was 120 miles above the surface of the earth, was 338 miles downrange, and was traveling just under 10,000 miles per hour!  It’s time to orbit was projected to be 21 minutes and I believe the orbital velocity would be approximately 18,000 MPH.  (The actual orbital velocity would obviously be a very exact number.)

When it was all over we carried our chairs back to our rig and then walked to Pat and Vickie’s coach so she could drop her’s off.  Pat went in for the evening but the three of us went for a leisurely midnight stroll around the entire campground.  In spite of the event that had just occurred the campground was quiet.  There is some general purpose street lighting here, but not too much.  It’s a nice campground and I could see why Pat and Vickie like to come here.

Back at our coach Linda decided to sleep in the living room.  More specifically, she decided to sleep in the two captain’s chairs by locking them in position facing one another, reclining the backs, and putting the hassock between them.  She thought she might sleep better in a partially upright position.  I finished a few e-mails and retired to the bedroom where I was joined by the cats.  I was too tired to write but too awake to go right to sleep so I turned on the TV.  After flipping through the channels I settled on an old movie, The Battle of Britain.  By 2 AM it was still on, owing to too much time for commercials and not enough time for the movie, so I turned it off and went to sleep.

The “Jetty” and pier at Jetty Park. Cape Canaveral, FL.

2016/03/23 (W) On The Road To Recovery

Linda slept seven hours last night with very little coughing, at least that I heard.  She slept in the living room (her choice) and left the bedroom to me.  I had a long early evening nap and did not fall asleep until 2 AM.  Even then I did not sleep that well and got up at 8 AM.  Linda was still asleep but woke up not long after.  She wanted coffee so rather than grind up beans and deal with the whole do-it-yourself process we walked up to the campground office with our two Tervis mugs/caps and filled them there.  Free coffee all day, every day, is a nice campground amenity and not one we have found anywhere else.

Pat and Vickie decided to go to Epcot Center at Disney World today for the annual flower and garden show.  Vickie texted me to see how Linda was doing and if we wanted to go.  Linda was definitely not well enough yet to go anywhere or do anything, so we stayed behind and had an easy day at our home on wheels, starting with toast and jam for our breakfast.  Linda read a little and checked our banking.  I talked to my sister about our dad for a bit, but spent most of the morning completing draft blog posts for the last three days.  We both got showers, which brought our fresh water level down to ~1/6th tank (20 gallons).

I copied the photos I’ve taken during the last week, including the rocket launch last night, to my computer.  I selected one of the rocket launch for this week’s post card, processed it, and e-mailed it to Linda’s iPad.  While she created a post card for grand-daughter Madeline, I connected the fresh water hose and water softener, tested the harness of the water supply, (7 to 10 gpg), filled the fresh water tank (100 gallons), and connected the waste water drain hose.

With my outside chores done I selected two photos from my article on replacing the bearings in a Webasto diesel burner and e-mailed the image numbers to Gary and Jorge at BCM.  They will be used on the “Coming in June” page of the May issue, one for my articles and one for Lloyd DeGerald’s multi-step maintenance list.

The nighttime launch of a rocket from Cape Canaveral Air Force Station as seen from Jetty Park. Note: This was a long-exposure handheld shot. I was braced against a sign to take it.

I heated a can of Amy’s Golden Lentil “Indian Dal” soup and washed some black grapes for our lunch.  There was a cool breeze outside but a bit of heat gain in the coach so we sat outside, doodled on our iPads, and dozed in our folding bag chairs.  A little before 5 PM Linda decided she wanted to go for a walk on the beach.  The wind was strong out of the east with 3 to 4 foot waves breaking just off shore, but the late afternoon sun was warm enough to make for a pleasant stroll south towards Cocoa Beach.  As the sun dropped lower in the sky and was filtered by thin clouds it turned slightly chilly so we turned around and headed back to Jetty Park.  We continued our walk through the picnic and playground area and walked along the channel to the boat ramps and then to the campground office.  We got a couple of cups of coffee and sat down to watch the news but the TV was tuned to FOX News, so we left and walked back to our site, noting that Pat and Vickie’s car was back at their site.

We discussed what to do for dinner and decided on cooking the vegan Italian sausage and using it to top a salad.  I texted Vickie to ask how the garden and flower show was, and let her know that Linda was feeling slightly better.  We gave the cats their monthly dose of Cheristin flea medication, which they were due for yesterday.

Vickie came over at 7:15 PM with her iPad and we looked at all of the pictures she took at the Epcot Center Flower and Garden show.  It was clearly a spectacular exhibition and since we could not attend we were glad to see it through Vickie’s photographs.  By the time Vickie returned to her coach it was almost 9 PM so Linda suggested that we just have granola for dinner.  That sounded quick and easy to me, besides which I love her granola, so I did not need any convincing.

On Wednesday evenings we like to watch nature, science, and technology programs on PBS.  We have two PBS stations potentially available to us here at Jetty Park Campground but neither of them have 100% reliable signals.  I experimented with a range of antenna directions and selected the one that seemed to offer the most reliable signal for the 24.n channels.  NOVA was on the recreation of Noah’s Ark and Secrets of the Dead was on the discovery of the Hanging Gardens of Babylon in Ninevah, 250 miles north of Babylon and built by King Sennacherib.

Linda once again set up the captain’s chairs as a bed so she could sleep sitting up.  I could not tune in channel 24 in the bedroom so I finished watching the show in the living room.  At 11 PM I tuned off the lights in the front of the coach and left Linda to sleep while I retired to the bedroom to write, play a few games, and watch a little more TV before going to sleep.

 

2015/12/28 (M) On to Arcadia

Even though we were pulling out this morning we did not set an alarm to get up at some particular time.  We were up by 7:30 AM anyway. I did not make coffee or have breakfast and started preparing for departure.  We packed up our computers and put them on the bed, put away remote controls, and turned off the laser printer and NAS.  While Linda cleared off counters and secured drawers I took care of some outside things.

I pulled the tow bar parts bags out, set them aside, got out the tow bar adapters for the car, and inserted them.  I folded up the two bag chairs and put them in the car and folded up the plastic table and stowed it in the front bay.  I checked the pressure in the two front/steer tires on the bus and they were fine so I did not have to get the air compressor and hose out.  I put up all of the awnings and opened the air valve for the engine accessories and toad braking system.

When everything else was ready Linda pulled the car out while I turned on the bus chassis batteries and started the bus engine.  I let the chassis air up, pulled up the tag axle, pulled out of our site, and then backed up until I was parallel with, and close to, the edge of the road on the passenger side and not blocking anyone’s driveway.  Linda pulled the car up behind the bus and we connected it for towing.  The breakaway cable finally broke so I got the spare cable out of the glove box but I could not get the key out of the disconnect.  Rather than risk breaking it and thereby disabling the car, we decided to travel without it.

We had a final, quick chat with our neighbor’s, Danny and Dorothy, and with Ken on the other side, and pulled away around 9:10 AM.  We were out of the resort and headed southeast on US-27 at 9:26.  At Ocala we headed south on I-75 as far as exit 301 (Cortez Blvd) at Brooksville, and headed east on FL-700 as far as US-98 and headed south.  Most of this segment was also co-terminus with US-35.  The drive was mostly rural and very pretty.  It was warm outside but patchy clouds kept the temperature inside the coach from getting too warm, at least for a while.  Eventually I turned on the OTR HVAC system and it worked well.

We passed through several smaller towns but eventually got to Lakeland which was much larger, with lots of stop lights and traffic, so it took longer to get through.  Still, it was an attractive community and something to see besides an Interstate highway.  The Detroit Tigers spring training camp is in Lakeland and we will likely drive up for some games while we are in this part of Florida.

US-17 joined up with US-98 as we were leaving Lakeland.  Somewhere south of Lakeland (Fort Meade?) US-98 turned east towards Sebring and we continued south on US-17 to Arcadia.  A few miles before reaching US-70 west of Arcadia we turned onto NE Turner Road which ran due south towards the Turner Agri-Civic Center and bypassed downtown Arcadia.  We pulled into the Civic Center, which was the rally venue, at 1:15 PM.

Linda checked in with rally organizers/hosts Bill and Brenda Phelan.  Linda stayed with the coach while Bill drove me over to check out sites.  I selected site #9 which would have us facing west with our passenger side facing north.  Although this orientation put the afternoon sun on our windshields, it also provided shade in conjunction with the patio awning.  Dan (?) led us over to the site and then left us to unhook the car and back the bus in.  We leveled the coach (we thought) and I shut it down and went through our arrival preparations.

The inside of the coach was cool from the OTR HVAC and I wanted to keep it that way, so we left the windows and roof vents closed and put the insulated foil panels in the three large skylights.  We also found the snap covers for the side windows next to the driver seat and installed those.  We were able to position the coach which generous space to our passenger side and far enough back that the 25 foot shorepower cord just reached the outlet box.  After plugging in we turned on all three of the residential air-conditioners.  We deployed all of the awnings, including the patio awning, to shade the windows and provide a shady place to sit outdoors.  We also have a fresh water and sewer connection but may not use them while we are here.  We are only here until Friday or Saturday and came in with a mostly full fresh water tank and mostly empty waste tanks.

Although it was very warm (86 degrees F) and humid the clouds had thickened and filled in during the second half of our drive and there was a good, steady breeze.  The bus ran well today including the OTR HVAC.  The low pressure light only came on briefly one time while I was idling at a stop light.  Apparently it works a lot better when it is relatively warm outside.

Once we were set up we had a light lunch of roasted red pepper hummus and sourdough pretzel nibblers with fresh apple slices and orange segments.  We then drove to Walmart to pick up some anti-itch cream and bought a few grocery items while we were there.  We checked out the filling station on the property and decided it was not a good choice for our bus.  We also found the entrance to Big Tree RV Resort which was, literally, across the street from the Walmart.  We drove back towards downtown and stopped at the Winn-Dixie to see if they had a better selection of boxed wines than the Walmart.  They did, and we bought a Franzia Crisp White.  We drove the rest of the way into downtown in search of a filling station with diesel fuel, and access for large vehicles, before returning to the rally site.

Linda wanted to go for a walk so we strolled past the buses and other RVs that were already here.  We ran into Scott Crosby working on Dan’s windshield.  We met Dan, Kathy, and their son James at the FMCA GLCC Surplus and Salvage Rally back in September.  Apparently the windshield on their GM PD4106 started coming out of its gasket along the top and caving into the cockpit on their trip to Arcadia.  Scott was up on a ladder getting the gasket reseated around the frame and glass.

We continued our walk and discovered that Paul and Claudine Elbisser, also from our FMCA GLCC chapter, were here.  We visited with them for quite a while before finishing our stroll around the rally and returning to our rig for dinner.  Linda microwaved a sweet potato and served the last of the Gardein stuffed mock turkey roll and broccoli that we had for dinner on Christmas day.

After dinner I tried tuning in OTA TV stations, orienting the antenna both WNW towards Tampa St. Petersburg, and due south towards Port Charlotte, Punta Gorda, and Ft. Meyers.  When I scanned for stations I found about 60 in each direction although many of them were the same stations.  So much for digital TV signals bring highly directional.  We watched reruns of our Monday evening TV shows on CBS.  We also turned on the Verizon Mi-Fi so we could get online long enough to check TV tower locations and network affiliations, check our e-mail, and change our location in RVillage.

I got an e-mail from Gary at BCM with the draft of the February 2016 issue and a request that I proofread Part 1 of my 2-part article on our Habitat For Humanity RV Care-A-Vanner build in July 2013.  I was a little tired from our day’s activities and was not in the humor to review articles, edit old blog posts, or write new ones so I just watched TV and fiddled with the thermostats and fan speeds on our air-conditioners.  I was puzzled by the fact that it felt humid in the rig in spite of the air-conditioners having been on all day.  The front and rear ones seem to be cooling better than the middle one, but the front one was the only one that we seaw water dripping from the drain line outside the bus.  I admit to having some level of concern about where the condensed water from the evaporators is going, assuming they are condensing any moisture.

The overnight low was forecast to be about 70 with morning fog, i.e., 100% relative humidity so in spite of the fan noise we left the bus closed up and the A-Cs running.  I adjusted the thermostats down to make sure the condensers would run, and lowered the fan speed in the bedroom to reduce the noise level.  I plugged the power in for the rear OTA TV antenna, but it was not functioning correctly and was clearly not going to fix itself.  It needs to be replaced but I am reluctant to buy another one of the same model as the failure rate so far has been 50%.  Linda read, and I played a few games, on our iPads and then went to sleep.

 

2015/12/01 (T) Home Again

I got up at 7:45 AM, got dressed, and fed the cats.  The Magnum BMK was showing the house battery pack at 24.2 VDC and 47% SOC with the refrigerator and other significant loads not drawing any power.  I worked on my iPad for a while until I heard muffled voices from the compound around 8 AM and saw Pat (John’s son) working on the roof of one of the trailers.  Linda got up at 8:30 and we had granola for breakfast and had a leisurely morning.

Check-in time at Williston Crossings RV Resort WCRVR) was noon.  We only had 75 miles to travel to get there and did not need to be there right at noon.  Around 10:45 we started getting the inside of the coach ready to travel and by 11:15 we were taking care of the outside stuff.  Paul and Eugenia were already hooking up their car and obviously preparing to leave as well.  We walked around the coach and checked that the bay doors were closed and locked.  On the way around we got the tow bar off the ground and secured it.  I then switched on the chassis batteries, opened the engine accessories air valve, and returned to the cockpit.

The chassis battery gauges read lower than normal for a fully charged condition but had plenty of energy stored in them to crank the engine quickly.  With Linda spotting from outside I did a three point turn to get the bus pointed towards the exit.  John came over in his Kubota utility cart and chatted with Linda while I moved the car behind the bus and we continued to chat with John as we hooked up the car.  We thanked him for his hospitality and assured him that we would be back; both for a solar system and to just hang out for a longer time in the woods by the Suwannee River.  I started the engine and Linda checked the lights.  Everything was good and when she was back on board we started the slow roll back to the county road.

We pulled out of John Palmer’s place around 11:30 AM and slowly made our way back to CR-354.  I stopped there (to check for traffic, of course) and raised the tag axle to shorten the turning radius.  I did not have a sign post at the edge of the road on the left, as I did when turning in, but the ditch on the other side was deeper closer to the road so I did not to get the passenger side steer tire very far off the pavement.  I completed the left turn cleanly and put the tag back down before continuing.

It was closer to 11:45 by the time we passed the east boundary of the property and saw the sign for the River Rendezvous RV Park.  We took CR-354 to US-27 and headed east to US-129.  Just south of Trenton we vectored off onto SE CR-339 and then picked up NE US-27 Alternate which eventually became Main Street in Williston.  The trip took about an hour and 40 minutes and we arrived at the main entrance to Williston Crossings around 1:25 PM.

It’s usually nice to return to a place you have been to before and liked.  We enjoyed our time here during winter 2013/14 and it felt a little bit like being home again in that the place, and some of the people, were familiar to us and pleasant to be around.  One of the most familiar people was John, our next door neighbor of two years ago.  He was doing site escort duty and led us to our site after Linda got us registered.  We pulled up in front of site #233 and disconnected the car while John read the electric meter.  John then helped me back onto the concrete pad.  We were in place and level at 2 PM and visited briefly with John, giving him a quick tour of our interior remodel.  After John left we hooked up the shorepower cord and put power to the coach.

I checked the chassis battery voltage on the dashboard gauges with the engine off and they were 28+ and 14.  We went through our usual arrival routine with the addition of checking the reading on the electric meter.  We pay for our electricity here so checking the meter on arrival is prudent.  I checked the maintenance chargers and they showed the charge level on the upper and lower 12V portions of the chassis batteries as 75% each.  They should have been fully charged after almost two hours of engine operation so something was still not right.  The house batteries were down to 24.0 VDC and showing a 43% SOC.  The battery charger section of the Magnum 4024 went into Bulk charging mode, charging the house batteries at 107 Amps.

We are parked facing approximately WSW so the front of the coach gets the afternoon sun.  It was in the low 80’s, and a bit warmer in the coach, but we turned on the ceiling exhaust fans rather than run the air-conditioning, deployed the window awnings on the driver side, and lowered the day screens on the inside.  We used AntennaPoint.com to locate broadcast TV towers.  The two we cared about, CBS and PBS, were both north of us.  I rotated the front antenna to point in that direction and did a channel scan.  They both came in with solid signals so I repeated the set up with the rear antenna and bedroom TV.

Once we were set up we had vegan hot dogs for lunch and then walked to the CVS Pharmacy just outside the front entrance to the resort.  We crossed paths with John again and this time he had Ali with him so we had a quick reunion.  When we got back to the coach I was tired and with the warm conditions I dozed off.  When I woke up I set up the printer, NAS, and Amped Wireless router.

Meanwhile Linda had started preparing red beans and rice for dinner and discovered that she did not have diced tomatoes.  I drove to the Grocery Depot, which is also just outside the front entrance to the Resort, and bought a couple of cans that included green chilies.  It was 6:30 PM and the Resort gates were already closed so I had to use the code to get back in.  The dish was excellent and would not have been the same without the tomatoes.

After dinner I e-mailed Butch, Chuck, and Lou.  We are parked close to one of the Resort’s Wi-Fi towers with a strong N signal and reasonable speed, leading me to wonder if the Resort has upgraded their system and Internet connection.  Linda made a stovetop apple crisp and finished it just before our Tuesday evening TV programs began at 8 PM.  The crisp was different from an oven baked one but still very tasty.  We watched a few TV programs on PBS and CBS.  Linda has been fighting something and took some OTC Tussin nighttime medicine for her cough, congestion, and itchy throat.  She has coughed enough that it now hurts and is very tired from many nights of poor sleep.

 

2015/11/30 (M) Palmer Energy Systems

I was up at 6:45 AM and wandered over to John’s trailer compound around 7:10.  He was outside talking to someone on his cell phone and we finally left at 7:20 for breakfast in Mayo.  We went to a small, unassuming diner and waited in the car until Dale showed up.  We ordered at the counter, selected ceramic mugs from a basket, and then took a table in the back.  I had a version of my usual breakfast out; dry toast with Smucker’s Strawberry Jam and coffee.

We were done by 8:15 and stopped at the NAPA store headed east out of town on US-27.  They had a good supply of Group 31 commercial batteries and gave me a good price based on my AITA/NAPA discount card and waved the core charge if I returned the old batteries.

We returned to John’s and I got busy removing the old batteries, which was a bigger project than it sounds.  I had to get all four of my tool boxes out plus our Little Giant ladder, nitrile gloves, and paper towels.  I also had to disconnect the car from the bus.

The four batteries were lined up, sitting crosswise, in a tray above the passenger side tag axle.  Being that far off the ground I found it easier to work from the Little Giant ladder configured as a short step ladder.

My first step was to make a diagram of the physical location of the batteries with the positive and negative terminals marked and lines for the main cables attached to each one.  I assigned the numbers 1 through 8 to the terminals and then used green Frog Tape to label each cable with the number of the terminal it was connected to.  At Linda’s suggestion I used my iPad to take a photo of the batteries with the labeled cables.

My next step was to remove all of the cables from the batteries, being careful not to allow the exposed lugs on the ends to come in contact with anything they should not touch.  Some of the cables were jumpers, which I removed and set aside, while others were captive and had to hang down next to the forward side of the tray.  The cables were secured with a lock washer and nut at each terminal which I set aside as I removed them.

With all of the cables removed I proceeded to remove the large nut that secured the retaining bracket that held the batteries and remove it.  I started with the battery farthest to the outside as it was the easiest to lift out from atop the ladder.  Paul, one of the owners of the Entegra Aspire motorhome parked behind us, had come over to see what I was doing and offered to help.  I gladly accepted his assistance and he helped me lift the old batteries out of the tray and get them on the ground.  Each one weighs about 80 pounds.

I emptied out part of the driver’s side rear of our Honda Element, loaded the four used batteries in there, and took off for Mayo.  The associate at the NAPA store unloaded the old ones for me and loaded the four new ones, which I appreciated.  He pulled eight new lock washers for the terminals and a larger one for the hold down bracket, got a 1/8″ brass pipe thread plug, and helped me select at spray lubricant for the tray slides and a grease to coat the connections after they were made to protect them against corrosion.

As best I recall I was back at camp by 9:30 AM and backed the car into position by the passenger side rear of the bus.  I used the silicon spray to lubricate the slide tracks.  I then moved each battery in turn from the car to the ladder, setting it up one step at a time until I could lift it into the tray and slide it into position.  I was careful to use my legs and protect my back muscles.

With the batteries physically in place and oriented correctly I reinstalled the hold down clamp.  I then got Linda to help me reattach the cables.  I cleaned the ends to remove previous grease and wrapped several of them in electrical tape to ensure they did not short out to the tie down bracket.  I put No-Ox electrical connection anti-oxidant on each terminal.  We then put the cables back on using the new lock washers and the old nuts.  I torqued the nuts tight and we double checked the connections against the diagram.  We finished at 12:30 PM, so I felt we had accomplished the battery replacement in a very good amount of time.

I turned on the generator and then turned on the circuit breaker for the maintenance chargers.  As I expected the new batteries were not fully charged but the maintenance chargers indicated at least a 75% SOC and we slid the battery tray back in to its compartment.  I repacked the tool boxes and Linda loaded them back into the battery bay.  We put the ladder back in the front bay and the things I had removed from the car back in there.

This old building seemed to be full of stuff but no longer actively used.  Our bus was parked pointing directly at it.

This old building seemed to be full of stuff but no longer actively used. Our bus was parked pointing directly at it.

At 1 PM we decided to go for a walk in the woods.  I turned off the genset, put on my hiking boots, and got the Sony a99 camera.  It was a lovely day for a walk with the air temperature at 80 degrees F but shaded from direct sunlight by the forest.  I took a couple of dozen photos along the way.  We were back by 2 PM and decided to drive into Mayo to see it and buy some groceries.  When we got back we had vegan cold cut sandwiches for lunch and then sat outside for a while.  Paul came over to chat followed by Euginia.  Doc (the retired veterinarian who owns the property) stopped by and then John drove up to see if we were interested in a campfire.  That sounded great so John said he would start one.

Linda sits in a tree swing in one of the areas that John has “improved” on the property.

Linda sits in a tree swing in one of the areas that John has “improved” on the property.

We took our chairs over to the fire ring and sat for a long time having a nice conversation.  Kathleen arrived in a car and joined the group.  We never learned who she was but we did learn that she was there to meet up with folks driving down from Atlanta.  On the short walk back to our coach we paused to marvel at the night sky.  It is very dark here at night and there were no clouds this evening.

For dinner Linda made linguine with mushrooms, sun-dried tomatoes, garlic, and olive oil.  It was very good.  She used the induction cooker and we operated off of the batteries/inverter so they got quite a workout.  After dinner I used www.antennapoint.com to locate the TV towers around us.  I managed to tune in a CBS affiliate so we were able to watch our usual Monday evening TV programs.  I worked at my computer off-loading photos from the camera and copying them to the NAS.  I e-mailed Butch and texted Chuck regarding the battery replacement.

Linda sits in a tree swing in one of the areas that John has “improved” on the property.

Our bus boondocked at John Palmer Energy Systems shaded from the late afternoon sun.

John suggested that we operate off of the inverter and batteries and run them down to 24.0 VDC which is approximately a 50% SOC, so I agreed to try it.  We had issues with the system during the evening.  The power was flickering, causing the APC UPS to switch to batteries briefly and the lights to flicker.  The TV even turned off once.  This has never happened before and I did not know what was causing it, but suspected that we might be using too little power and/or that the inverter had overheated (although I considered that rather unlikely).  I ended up turning off the NAS and the Amped Wireless router, which were plugged in to the UPS, and then shut off and unplugged the UPS.  My laptop runs on its own battery, of course, but I had already checked my e-mail, off-loaded photos from the camera, and backed up photo files to the NAS, so I turned it off as well.

I also turned off the Search Watts feature on the inverter, which was set to 5 Watts.  My understanding is that this feature turns off the inverter when there is no load and turns it back on when a load of at least 5 Watts tries to draw current.  Five Watts on a 120 V AC system is 5/120 = 1/24 Amp or slightly more than 40 mA; not very much.  On a 24 V DC battery bank the required draw from the batteries, ignoring inverter inefficiency, would be five times that (120/24 = 5) or 200 mA = 0.2 A.  The Magnum remote was showing that we were drawing at least 6 A, so that should not have been a problem, but I did not know what else to do and I certainly was not going to bother John at this late hour.

John also suggested that I equalize the batteries and told me how to activate that function on the Magnum 4024 by holding down the button on the unit for at least 25 seconds.  The equalizing charge is a 4 hour cycle and he suggested I run it twice, back-to-back once the batteries were fully recharged and the charger was in float mode showing zero Amps.  He told me to run the equalizing charge once every six months.   I have always read that you should NOT apply an equalizing charge to AGM batteries but John said that the two guys who own Lifeline Batteries now recommend this.

We went to bed a little after 11 PM.  Linda fell asleep almost immediately but I was awake until 1 AM working on this post and listening to the sounds of the coach.