Tag Archives: Schramm’s Mead

2015/05/28 (R) Ice Cold Internet

I was up until after 1 AM last night fussing with my computer but the OS was updated and was running better (I think) when I finally went to bed.  I need my beauty rest so I did not get up until 9 AM this morning.  Linda had already made coffee so I checked the temperature of the refrigerator (41.4 degrees F) and then got out the soy creamer.  41 is better than 45 but given where the thermostat was set the temperature in the fresh food compartment should have been 35 degrees or lower.  We had a very late breakfast of homemade granola and small glasses of orange juice to wash down our vitamins.

Because I did not get to upload any blog posts last night I switched up my routine and spent the morning working at my desk.  The weather was very nice so Linda went for a long walk.  My computer was back to normal and I managed to upload nine posts to my blog (May 10 through 18) by 1 PM.

I had an e-mail back from Ken Schramm yesterday letting me know that his “last day at Wayne RESA” gathering would get underway around 3:30 PM at Ashley’s Beer & a Grill at Westland Mall.  Brendan and Shawna’s celebration is from 5 to 8 PM in Ann Arbor so we will be able to attend both events although we might not make it to Ann Arbor until 6 PM.

Today was our friends’ 44th wedding anniversary.  Butch and Fonda were married the same year we were one day before us.  We did not know each other then but are now friends through our mutual passion for converted highway buses.

Brendan called and talked to Linda.  It turns out that tomorrow is grandparents/special friends Shabbat at Madeline’s daycare center and Brendan thought we might want to attend.  It starts at 10:30 AM and includes lunch.  The food at the daycare center is vegetarian but not vegan so we will see how that works out.  Brendan is going to take care of Linda’s plants so we will take these with us and go to his house when we are done at the daycare center.  I will pick up our electric pressure washer while we are there so I can wash the bus on Saturday.  We were going to buy cards today for Ken, Brendan, and Shawna but decided we would do that tomorrow on our way to Ken’s gathering.

Linda made large green salads with chickpeas for lunch.  We both put on a few pounds over the winter and really want/need to take them off.  After lunch I worked in the bus.  I removed the wood trim along the top of the beveled strip mirrors on the wall in hallway.  The strips were glued directly to the wall so I put the trim back on.  If we do not want to see these mirrors we will have to figure out some way to cover them.

There was a triangular horizontal panel between the upper edges of the J-lounge and the dinette with four switches mounted in it.  Two of those switches no longer control anything but the other two still do.  I secured the panel above the passenger side HVAC chase and blocked it in so it could not move.  I dressed all of the loose wires with cable ties and cable clamps and secured them to the floor.  I cut two grates from a piece of expanded metal and secured them over the two holes in the driver side HVAC chase where the sleeper-sofa was installed.  That sealed up the last of the holes that the cats might get into.  If one of them got into the HVAC system we would have disassemble half the bus to get them out.

I removed all of my tools and miscellaneous parts from the bus and set them on steps leading to the house.  I had put one of our folding chairs inside the bus to sit on and moved it to the location of the passenger chair as a safety barrier after I moved the trash can out yesterday.  I folded it up and put it back in the bay where it is stored.  While Linda vacuumed the inside of the coach with our Shop-Vac I put tools and parts in the garage or back into the appropriate tool boxes.  When she was done we got the Shop-Vac out of the bus and put it in the garage.

There is a maple grab handle on the right side of the entrance stairs (as you enter the bus) attached to a piece of maple trim from the back side.  The finish is worn and the handle is loose.  I wanted to tighten it, which required access to the back of the trim board.  Linda recalled that we had Creative Mobile Interiors (CMI) tighten this handle when we first got the coach so we figured there had to be a way to get to the back of the trim board.

We removed the cockpit HVAC access panel just below the trim board but it did not appear to provide access to the back of the trim board.  I removed the only two screws I could see (at the right end of the trim) but it still would not come loose.  I figured the trim board had to be screwed on somewhere else and the only possible place was under a piece of inset brass finish trim.  This brass trim is used throughout the bus, including around the edges of the Corian counters, and has an adhesive backing.  I have found screws under it in other places so I pried the end up and peeled it out, revealing three screws.

I thought I was on the verge of success until I removed the three screws but still could not get the trim board loose.  I tried prying it at various points with a screwdriver but it would not budge and we finally came to the unhappy conclusion that it was glued on.  Perhaps it is secured from underneath in some manner that we did not see but I will have to return to this when I have more time.  Linda suggested that we cut the handle off and install a new one that can be screwed on from the front.  She’s a clever girl.  As long as the access panel was off we vacuumed out the cockpit HVAC system and then replaced the panel.

About this time a UPS truck went by headed deeper into our neighborhood.  Since we live on a dead end street I knew the truck would be coming back so I waited for it and flagged down the driver.  I explained to the young man that we had two packages delivered to the wrong house in the same week about a month ago and that I had called the 800 number and talked to customer service but I would appreciate it if he would mention it to his colleagues as we will be ordering a lot of stuff starting in the second week of June.  He was very nice and said he would.

Our last bus task for today was the hard one.  We moved the passenger chair from the garage back to the bus using a hand truck so we did not have to carry it.  It is very heavy but with Linda guiding the top and me supporting the base we got it inside and set in position.  We tilted it fore and aft so I could slide the mounting studs into position and line them up with the holes in the base.  I then bolted it down to the support rails by tightening the four nuts.

This was all trickier than it sounds.  The bolts have square flanges that have to engage in the open slot of the channel to keep them from turning while being tightened or loosened.  But that required me to pull up on the studs as the nuts were not going on that easily.  As when I took the nuts off, I had to wedge one of them up with a screwdriver while I got the nut tight enough that the bolt would not spin.  I reconnected the power to the chair and we checked that all of the adjustments still worked, especially the footrest.

With the installation of the passenger seat we were done working on the bus until after GLAMARAMA and have two seats with seatbelts so we can tow the car rather than drive it separately.  This will be much nicer for us and the cats, although I expect the modified interior will freak them out initially.  We will be gone most of Friday but have Saturday to prepare food, reload the coach for the week, and wash the exterior.  Oh the joys of owning a converted coach.

For dinner Linda served the last of the whole wheat capellini with Portobello mushrooms and asparagus and steamed some broccoli.  A piece of whole wheat bread and a small glass of Leelanau Cellars Winter White wine completed the meal.  We had watermelon for dessert later.

I returned to my office after dinner and updated our Rand-McNally RVND 7710 GPS.  I then continued uploading blog posts.  By the time I quit working around 10 PM I had uploaded nine more posts and was caught up!  I think 18 posts in one day may be my all time record.  I did not get to work on articles for BCM, or copy files between our NAS units, but I was satisfied with what we had accomplished today.

 

2013/12/21 (S) Winter Solstice

Often referred to as “the shortest day of the year” the winter solstice is the exact same length as every other day of the year.  What’s special about it is that in the northern hemisphere it is the day with the least time from sunrise to sunset and the most time from sunset to sunrise.  From here to the Summer Solstice the minutes of daylight increase slightly each day.

As glad as we are to be headed south, there are always reasons to stay home.  Family tops the list, especially birthdays and holidays, but we took care of that with the cooperation of our families.  We have our friends and clubs, of course, but another reason would be the Winter Solstice Special Release Party at Schramm’s Mead in Ferndale.  Since we could not be in two places at once, we will just have to hope that Ken still has some Winter Solstice left when we get back.  🙂  If not, perhaps Ken will have a Vernal Equinox Special Release or a Summer Solstice Special Release.  Any excuse to buy Ken’s mead.

What we did instead was pull out of the Oh! Kentucky RV Park/Campground at 8:20 AM and drove 0.3 miles to get back on southbound I-75.  It was dry but overcast as we started out, but we were in and out of rain for most of the drive.  The rain was generally light, but we did encounter heavier rates from time-to-time.  We did not experience much fog, but we did have some areas with ground clouds.  We made it past Knoxville, Tennessee without the problems we had back in October.  This was the farthest south we have been with the coach, and the first time I have driven I-75 south of Knoxville.  We made a brief stop for fuel at the Pilot Travel Center in McDonald, Tennessee and continued south on I-75 into Georgia.  This the first time I have driven anything in Georgia and the first time we have had the coach there.  Even with the rain it was a relatively easy and uneventful drive, except for the continued, almost random, on/off of the Check Engine Light.  The coach ran well with good power and all of the gauges indicated normal operation, so we just pressed on.  When we get settled in Arcadia for the rally I will pull out the ProLink and read the codes.  That should draw a crowd and might even make for an interesting round-table discussion.

At 1:30 PM we took exit 111 and headed west 0.3 miles to the entrance of the Cartersville/Cassville-White KOA, This was our first time staying overnight in the Georgia in the motorhome.  Linda had called ahead when we were near Knoxville, Tennessee, so we knew the office would be closed from 11 AM to 3 PM.  The office manager left a map of the campground for us in the night registration station with our spot marked on it and the route to take through the campground to get there.  She even put an orange traffic cone at the entrance to our site to mark it as reserved; very thoughtful.  The temperature was in the low 60s when we arrived and rose to 69 during the evening.  Rain was forecast for the later evening and thunderstorms for the overnight.  As we have done since before we left, we kept an eye on the weather.

This is the second KOA we have stayed at in the last three months.  We tend to think of them as overpriced with lots of amenities that appeal to families with kids, but that we don’t use.  Both parks, however, have been very good places for us to stay, with:  convenient access; good gravel interior roads with sufficient width and turning radius for our rig; mature trees trimmed up high enough to not scratch our motorhome; pull through sites with 50 amp full hookups; and clean bathrooms with good showers.  The one in Natural Bridge, Virginia was full of kids, but it was a weekend near Halloween and we had fun giving away candy to the trick-or-treaters.  The current location appears to be no more than 40% of capacity, with no evidence of kids; definitely off-peak season.

As an update to yesterday’s post, I discovered that I was pushing the wrong button and that both windshield washer pumps do, in fact, work.  Duh.  L  The good news was that both windshield washer pumps work!  J  When we got to our destination I switched the output hoses back to their correct pumps so everything should work the way it’s supposed to tomorrow; except perhaps for those clogged orifices on the lower wiper arms.  It’s always something, it seems, and any RVer who is honest about it will admit that.  But they will also tell you that it’s part of the experience/lifestyle, and you either learn to take it stride and deal with it or you end up doing something else.

As a final technical note, now that I have started valving off additional circuits on the auxiliary air system, the pressure seems to be holding much longer and thus the compressor runs much less often.  It is now at least a two hour cycle and may be holding longer than that.  The new auxiliary air distribution/control panel that I built last year and installed this past spring has made it possible to do this.

2013_11_08-15 (F-R) Another Busy Week

The second week of November was another one of those weeks where we were busy every day from the time I got up until the time we went to bed, but I don’t have a clear recollection of what I was doing each day as I did not always mark it on my calendar.  I think that is because I spent a lot of time at my computers working on WordPress websites and installing packages/updates.  Some days are very clear, however.

2013-11-08 (F) The “Eyes” Have It

We had managed to snag a couple of appointment times this morning to have our eyes checked by our long-standing optometrist at the Farmington Vision Clinic.  Linda’s eyes had not changed very much, but it had been a couple of years since she got new glasses, so she decided to get a pair.  I had been experiencing intermittent “wavy” patterns and was a bit concerned about that.  The exam did not indicate any issues with diabetes or glaucoma, so that was a relief.  The tentative diagnosis was “pre-migraine ocular disturbance” which was interesting because I was not experiencing any headaches, and rarely do.  The trigger may be something that I eat, perhaps caffeine or wine, so I may need to keep a food log.  Ugh.  I like writing about the dishes Linda prepares, but I don’t like “logging” my food intake.

Chuck is in the process of prepping their bus for southbound travel, so I met up with him for lunch.  He had also gotten connected to a guy in California whose older brother was living in Michigan when he passed away back in June.  The older brother was well known in the Prevost bus community, and had a converted coach stored in the N.E. suburbs of the Detroit Metro Area.  The surviving brother needed to deal with as part of his brother’s affairs, and Chuck had offered our assistance on Sunday.

2013_11_09 (S) Schramm’s Mead

But first we had to deal with Saturday, which started with our usual ham radio club breakfast in South Lyon, Michigan.  Attendance varies, but we had a big crowd of at least 20 people.  After breakfast we decided to drive over to Ferndale and find Schramm’s Mead.  I worked with Ken Schramm before I retired from Wayne RESA.  He’s still the TV / Multi-media Production Manager there, but outside of normal business hours he is a well-known expert on the subject of mead, having written a well-respected book on the subject, and speaking at international conventions.  He and his wife Jean and their daughter Alison have been working for over a year to get Schramm’s Mead open, and that finally happened about 6 weeks ago.  They are at 327 W. 9 Mile Rd. in Ferndale, Michigan.  The meadery is located in a very “happening” part of town just a short walk west of the intersection of 9 Mile Rd. and Woodward Avenue and should be a good location for them.  Parking was plentiful, with both paid and free options.  We sampled their complete line of currently available mead products and bought three bottles.  I have added a section to the Health & Food tab of this website on Wine & Mead and refer you there for more information about mead and the offerings from Schramm’s Mead.  Let me just say here “this is good stuff.”

2013_11_10 (N) Buses & Ham Radio

Sunday found me headed to Chuck’s house near South Lyon bright and early, or at least early.  We needed to meet the guy from California at the RV storage lot in Shelby Township, so it took an hour to get there.  He was waiting for us, let us in, and led us to the bus.  It was a 1997 (~) Prevost XL (40’) Royale Coach conversion with a Detroit Diesel Series 60 engine and 6-speed automatic transmission.  It appeared to be in good shape and Chuck and I set about figuring out its state.  The chassis batteries had been left “on” and were drained.  The house and generator batteries were also “on” but appeared to be in better shape.  It did not appear to have much fuel in the tank, but with the chassis batteries drained we couldn’t get accurate readings from any of the gauges.  We got the generator started, plugged in the 24V emergency chassis battery charger, turned the house batter chargers on, and set about finding the circuit breakers and switches seeing what worked.

After letting the generator/24V charger run for several hours the chassis batteries showed no sign of coming back to life.  We still had enough hours of daylight to do something about it.  We located a NAPA Auto Parts Store less than 2.5 miles from the storage yard and gave them a call.  They had 8 of the type battery we needed (12V Group 31).  We only needed four.  We pulled the old ones out of the bus and headed over.  By taking the old ones we did not have worry about disposal/recycling of them and avoided a “core charge.”  We installed the new batteries and the DD-60S fired right up.  That’s was a beautiful thing to hear.  The chassis and brake systems aired-up correctly and the gauges all came to life.  That’s was a beautiful thing to see.

The bus had about ¼ tank of fuel indicated, or about 40+ gallons, so we decided we did NOT need to drive it someplace to fuel it right that minute.  The bus was headed to Staley Coach in Nashville, TN at the end of the week and could stop for fuel early in the trip.

I had a ham radio club meeting at 6:30 PM, and needed to get dinner, so Chuck and I made our exit and headed back to his house.  I got home in time to change clothes but not sit down and eat.  Linda made sandwiches for us to eat as we drove to the meeting.

Our November ham radio club meeting is a significant one as we elect officers for the coming year.  Mike (W8XH) agreed to run for a 2nd term as president, Paul (N8BHT) agreed to run again for Treasurer, and I (K8BRF) agreed to run again for Vice-President.  Marty (KB8JIU) did not wish to run again as Secretary, and Harvey (AC8NO) agreed to run for that position, which he has held in the past.  There being only one candidate for each officer, the slate was declared elected.  The program for the evening was put on by Mike (W8XH) and Steve (N8AR).  They demonstrated the use of Mike’s Vector Network Analyzer (VNA) to examine the characteristics of an antenna by calibrating out the effects of the transmission line.

Technical note:  Transmission lines have losses, i.e., they inherently dissipate as heat some of the energy they are trying to transfer from a radio transmitter to an antenna.  The losses depend on frequency, and if the transmission line is of low quality it will dissipate more energy per linear foot than a higher quality one at any particular frequency.  How much energy it dissipates thus depends on the inherent loss, the length, and the frequency of the signal.  When a transmitter sends energy through a transmission line it would ideally like all of the energy to reach the antenna, be transferred into the antenna, and cause it to resonate, producing electromagnetic radiation.  It never works quite that well in practice.  If there is a mismatch between the transmission line and the antenna, some of the energy will be “reflected” back down the transmission line towards the transmitter.  However, if there are sufficient losses in the transmission line the reflected energy never makes it back to the radio, which makes the radio think everything is just fine when in fact very little of the energy the radio produces may get turned into useful RF EM radiation.  Mike’s VNA allows the user to “calibrate out” the effect of the transmission line and “see” what is actually happening at the antenna.  That’s cool, and that’s a good thing to be able to do.

2013_11_11 (M) Odds ‘n’ Ends

Monday was a catch-all day for me while Linda went to Ann Arbor for her regular Monday babysitting duty.  I talked to Michele and she was encouraged that she would be able to fix the two expensive body panels that I crunched.  I called Prevost and ordered the 3rd panel that she would not be able to fix.  It would ship via UPS and arrive on Wednesday.  I updated my LinkedIn account and added all three of our phone numbers to the Federal DO NOT CALL LIST, a long overdue chore.  I called Adams Well Drilling and Water Treatment to get new whole-house sediment filters and chlorine tablets for the carbon filter unit.  We have a sediment filter housing that takes 10” long large-diameter filter elements.  They are a spun polypropylene with a dual micron rating; 50 microns on the outside and 5 microns on the inside.  It’s like having two filters in one!  The 50 micron portion removes the larger sediment that can quickly plug and filter and render it useless, leaving the 5 micron filter to remove only smaller particles.  The flow rate through this filter is excellent, and it’s easy to change thanks to the pre- & post-filter shutoff valves Adam’s installed, and the pressure relief button on top of the housing.

We had previously arranged to meet Kate for dinner.  Having just seen her in Ypsilanti, we agree to meet at the Zukey Lake Tavern in Pinckney, Michigan.  Linda and I wanted to check it out as our ham radio club had decided to go there for our December holiday meeting/dinner.  They have a very average salad bar, but I was able to get plenty to eat at it.  Linda had a veggie burger.  Not a great choice for us as restaurants go, but it will work well for the club.

2013_11_12 (T) Madeline Comes To Visit

Linda had agreed to babysit our grand-daughter on Tuesday so our son could continue working on a presentation for his department at the University of Michigan Ann Arbor.  I don’t get to see Madeline as much as Linda does, so our son offered to bring her to our house and work there while Linda and I handled baby duties.  Madeline is a busy little girl.  She is an accomplished crawler and is working on standing up and walking.  She loves her books and toys, and grandma bought some new ones to have at our house for her.  She kept us both busy while her dad worked on his computer.  He brought her Pack-n-Play and set it up in the bedroom that we have designated for her.  She went down for nap right on schedule at 2 PM and slept for ~90 minutes.  We got to play with her until sometime after 5 PM when it was time to leave.

2013_11_13 (W) & _14 (R)

Linda had called a couple of weeks ago and managed to get an appointment with our primary care physician for her annual physical due to a cancellation.  Her total cholesterol had risen a little from the last visit, which annoyed her given the way we eat, but her HDL, LDL, and triglyceride numbers all looked really good.  She was also able to talk to the nurse and find me an appointment time later in the month.  I really did not want to wait until late April or May for my next physical.

Thursday morning I went to Chuck’s bus garage to chat with him and our mobile Mechanic, Joe Cannarozzi, who had come in from Chicago to complete some work on Chuck’s coach.  Joe had also been engaged by the guy from California to drive the bus to Staley Coach near Nashville, Tennessee on Friday morning and bring the guy back to the Detroit area.  It turned out that Chuck needed new brake pads for his tag axle wheels.  We were sitting around wringing our hands about how to get those in time for Joe to finish the brake job when I realized that Joe was going to Nashville where Prevost has one of their major factory parts and service centers!  Phone calls were made, parts were ordered and put on account for will call, and it was agreed that Joe would pick them up on Friday and bring them back with him.  Sometimes bus stories do have happy endings.

I spent Wednesday and part of Thursday working at my computers.  Larry (K8UT) is a member of our ham radio club and a very accomplished web designer.  He had given me the “key” to getting a local web-server running:  LAMP (Linux, Apache, MySQL, and phpMyAdmin).  I got MySQL and phpMyAdmin installed on the Linux box but was unable to create the databases I needed in spite of spending time with the documentation.  By Thursday evening I still did not have WordPress running on our local web-server, but I was clearly making progress in that direction.  Sometimes computer stories have happy endings too.